Munsch MAK-32 Скачать руководство пользователя страница 12

 
 

Hand Extruder MEK-32 / MAK-32 

 

Page 12/20 

Issue 12.2009/Rev. 02 

MUNSCH Kunststoff-Schweißtechnik GmbH 

 

 
5.4.5  Shutoff  

 Observe section “Safety”.  

 

   After completion of the welding job, switch off 

the drive unit and deposit the hand extruder as 
shown in the illustration (see preceding section).  

 

 Do not leave the hand extruder unattended.  

 
5.4.5.1 Hand extruder with integrated air supply, 

type MAK

 

 

  Press “return“ button once to switch off the 

heating circuits. 

 

 

 

 

 Maintain the air supply of the hand 

extruder until the unit has completely cooled 
down!  

  Pull mains connector. 

 
 
5.4.5.2 Hand extruder with external air supply, 

type MEK 

 

 

  Press “return“ button once to switch off the 

heating circuits. 

  Pull mains connector. 

 

 

 Maintain the air supply of the hand 

extruder until the unit has completely cooled 
down!  

 

 Never use water or another coolant to  

accelerate the cooling process! 

 

 

 
 
5.4.6  Transport/Storage 
Make sure to observe the instructions under section 
“Transport/Storage“.  
 
 
5.5  Set temperatures on temperature controller 
The default settings for the melt and air temperatures 
of the MEK and MAK hand extruders are shown in 
the following temperature chart.  
(The values have been determined with the aid of 
reference materials.) 
 
    
 
Temperature chart for MEK/MAK 
 

Material 

Melt temperature 

Air temperature 

PP 

200 – 240 °C 

250 – 300 °C 

PE 

200 – 240 °C 

250 – 300 °C 

PVDF 

240 – 260 °C 

280 – 350° C 

 
If other temperatures are needed the corresponding 
settings can be made on the temperature controller.  
 
 
 
5.5.1  Set temperatures   

 

 

 
 
 
 

 
 

Содержание MAK-32





















Отзывы: