Munsch MAK-32 Скачать руководство пользователя страница 11

 
 

 

 

 

MEK-32 / MAK-32 

Issue 12.2009/Rev. 02 

Page 11/20 

 

 
 

 

Hold and touch the hand extruder only on 

the handles provided for this purpose.  

 

     

D02-0001

 

 

 

 

  CAUTION The melt temperature must have 

reached the preset start interlock temperature 
for the startup timer to be activated. After the 
startup timer has timed out, the start interlock will 
be released and the extruder can be started. 

       
   
                                    
5.4  Welding with the hand extruder 

 Observe section “Safety” and the data sheet.   

 
General 
Welding is to be carried out in accordance with the 
guidelines of the German Association for Welding 
Technology (Deutscher Verband für Schweißtechnik 
DVS). 

 

The parts to be joined and the welding rod must be 
clean and dry. 
 
 
5.4.1  Introducing the welding rod 
 

  CAUTION  The hand extruder is provided with a 

bore for introducing the welding rod

 

 

 
       

 

 

 
5.4.2  Replacement and aging of welding rod 

  If the welding rod is to be replaced, make sure 

that any remaining rod in the hand extruder is 
completely removed. 

  For this purpose, operate the preheated hand 

extruder with the new welding rod until clean new 
material discharges. 

  The DVS guideline also recommends this 

procedure for hand extruders which have been 
out of service for prolonged periods while still 
being filled with welding rod.  

 

Ensure safe and environmentally 

compatible disposal of any waste generated. 

 
5.4.3  Welding direction / rate 
 

  The pressure of the discharging extrudate causes 

the welding shoe (and hence, the hand extruder) 
to move in welding direction.  

  See DVS Guidelines for the welding rate.  

 

   

D02-0026

 

 
5.4.4  Interruption of work  
 

 

 Observe section “Safety“. 

 

Do not leave the hand extruder unattended. 

 

Make sure to maintain the air supply. 

  When interrupting the welding job, switch off the 

drive unit and deposit the hand extruder as 
shown in the illustration below. 

   

        

Содержание MAK-32





















Отзывы: