Munch Machine CON-1204R Скачать руководство пользователя страница 24

 

24 

and cleaning instructions are provided with the equipment to assist plant growers and harvesters in 
developing their internal cGMP procedures.

 

 

 

Storage  

This conveyor must be cleaned before storage and stored in a clean and dry environment. Issues arising 
from improper storage are not covered under warranty.  

 

 

Limited Warranty  

We warrant for 5 years from purchase date and only to the original buyer (Buyer) that our products 
(Products) are free from defects in material and workmanship. If Buyer discovers a defect, the Product 
will be repaired or replaced at our discretion. That is the extent of our liability and obligations under this 
Warranty and, upon expiration of the applicable warranty period, all such liability and obligations shall 
terminate. We reserve the right to require proof of purchase for all warranty claims. 
WARRANTY EXCLUSIONS: 
We do not warranty Products against normal wear and tear (such as rollers, belts, wipers, bearings, or 
coupler wear, etc.), unauthorized modifications or alterations, improper use, improper maintenance, 
accident, misuse, negligence, damage, or if the Product is used for a purpose for which it was not 
designed. This Warranty gives you specific rights, and you may also have other rights which vary from 
state to state. Except for expressly stated in this Warranty, we shall not be liable for direct, indirect, 
consequential, incidental, lost profits, lost revenue or failure to realize expected savings, as well other 
damages arising out of, or resulting from the/your choice to use and the use of the Product. This 
Warranty is in lieu of all other warranties, express or implied, including, but not limited to, implied 
warranties of fitness for a particular purpose (some states do not allow the exclusion or limitation of 
incidental or consequential damages or allow limitations on the duration of an implied warranty, so the 
above exclusions may not apply to you). 

 

Customer Service 

Phone:  

541-371-2825 

 
Email:  

[email protected] 

 

Mailing Address: 

Frazer Industries, LLC  
DBA: MUNCH Machine 
PO Box 6764  
Ketchum, ID 83340 

 
 

 

 
 
 
 
 
 
 

Содержание CON-1204R



























Отзывы: