background image

G.

Lever turned 

90° clockwise:

shaft turns 

clockwise

8. Remove the handles.
9. Position the motor support onto 

the boring bar operating square. 

Ensure guide columns are lined up 

with housings (

D.

). 

NOTE: There is an opening at the 

very top of the shaft. This is to 

allow the insertion of a pin, which 

ensures that the motor support 

bushing does not slide out (

e.

).

10. Connect the hoses coming from 

the hydraulic control unit to the quick 

couplings of the hydraulic operator 

ensuring the lever is in the neutral 

position (

F.

).

MUELLER

® 

 

Shur Stop

TM

 Unit 812 PE Line Stopping System

Operating Instructions

8

11. Start the hydraulic control unit.
12. Turn the hydraulic distributor 

lever clockwise (

G.

). 

13. Insert the removable handle in 

the drilling machine.

5. Lift and position the drilling 

machine onto the slide gate valve in 

the open position. Tighten the bolts 

in a criss-cross fashion (

C.

).

       CAUTIoN: After each opening 

and closing of the valve, remove 

the operating wrench to prevent 

accidental movement.

6. Insert the removable handles 
7. Lower the shell cutter to the pipe 

by using the removable handles 

placed on the head of the drilling 

machine, turning them clockwise 

until contact is made with the 

pilot drill on the pipe. When this 

occurs, turn the feed tube a quarter 

turn counter-clockwise to avoid 

jamming when drilling begins.

!

C.

F.

Hydraulic

Distributor

Lever in Neutral Position: 

Shaft Stopped

Pipe coming 

from Hydraulic 

Control Unit

Pipe coming 

from Hydraulic 

Control Unit

e.

Anti-

Slide

Pin

D.

Graduated

Scale

Collar

Motor 

Support

Bushing with 

Control Screw

Guiding

Columns

Содержание ShurStop 812 PE

















Отзывы: