background image

952.5-0000010 OM 

 

107

4.3.3.4.2 Installation of crossbar and rear ends of split lower links in operation position  

 

Tractors “Belarus-952.5” with a draft control unit and split lower links are delivered to the cus-

tomer with crossbar (DH-1ZH) and rear ends of lower links as it’s shown in Figure 4.3.12.    

For mounting of the crossbar in operation position (as it is shown in Figure 4.3.12 b) do the fol-

lowing operations: 

-  unlock and remove eyes 3 (Figure 4.3.12), take off crossbar 4; 

unlock and remove pins 2, take off rear ends of lower links 5;

 

mount crossbar 4 on front ends of lower links 1, as it’s shown in Figure 4.3.12 b, fix it 

with eyes 3, pins 2 and splints;

 

attach  limit buckles 6 to  eyes 3.

 

 

 

 

 

 

1 – front ends of lower links; 2 – pin; 3 – eye; 4 – crossbar; 5 –  rear ends of lower links; 6 – 

limit buckle. 

 

Figure 

4.3.12 

– 

Installation of the crossbar in operation position

 

 

 

For installation  of rear ends of lower links 5 (Figure 4.3.12) you should remove crossbar 4, fasten 

rear ends of lower links to front ends of lower links 1 with eyes 3, pins 2 and splints, attach limit 

buckles 6 to eyes 3.   

 

ATTENTION: YOU CAN OPERATE THE TRACTOR ONLY WITH MOUNTED CROSSBAR 

OR MOUNTED REAR ENDS OF LOWER LINKS. MOUNTING OF CROSSBAR AND REAR 

ENDS OF LOWER LINKS AT THE SAME TIME IS FORBIDDEN! 

 

ATTENTION: TRACTOR “BELARUS-952.2” MOVEMENT  WITH ATTACHED IMPLEMENTS 

MOUNTED TO DH-1ZH  WITH THE SPEED ABOVE 15 KM/H IS FORBIDDEN. 

  

IT IS FORBIDDEN TO COUPLE TRAILERS AND SEMITRAILERS TO DRAWBAR HITCH 

DH-1ZH. 

 

 

During tractor operation with drawbar hitch (DH-1ZH) buckles should be blocked in operation posi-

tion. You should mount lower links with crossbar 4 horizontally and block buckles in operation po-

sition as it is written in section 4.3.3.1 “Buckles”  

 

Notice – General parameters and characteristics of drawbar hitch DH-1ZH are represented in 

subsection 4.4 “Drawbar hitches”  

 

4.3.3.4.3 Telescopic lower links and twin crossbar 

Against order “Belarus” tractors can be equipped with enforced RLL and telescopic lower links, 

which are mounted on the axle Ø35 mm instead of Ø32 mm (on tractors with draft control unit 

the additional axles are also Ø35 mm). If it is necessary, you can regulate step by step the 

length of telescopic links within 

±

80mm from middle position (as result the length of links can 

be 805 mm, 885 mm, 965 mm), hoisting capacity changes in this case (805 mm – the highest 

hoisting capacity, 965 mm – the lowest).

 

b) 

Installation  of the crossbar in operation position

a) 

Position of the crossbar and rear ends of lower 

links while delivery

 

Содержание BELARUS 952.5





























































































































































































Отзывы: