MTU 20V4000GX2 Скачать руководство пользователя страница 99

Страница: 99 / 143

Open threaded vent plug (5) of contaminated
filter.

Unlock drain valve (6) by pressing toggle and
open it.

Drain water and contamination from filter.

Close drain valve (6).

Remove screws securing the cover and take
off cover (2).

Remove spring housing (4) and filter ele-
ment (3).

Insert new filter element (3) and spring hous-
ing (4).

Fill filter housing with clean fuel.

10.

Place new gasket in cover (2).

11.

Fit cover with gasket and secure it with
screws.

12.

Cut in the cut-out filter again.

13.

Close threaded vent plug (5) when fuel
emerges.

14.

Set adjustable pointer of differential pressure
display instrument (→ Page 94).

M015565/03E 2016-02

| Fuel Filter | 99

TIM-ID: 0000004944 - 006

Содержание 20V4000GX2
















































































































































Результаты поиска

Содержание 20V4000GX2

Отзывы:

Похожие инструкции для 20V4000GX2

Бренды по названию

Популярные бренды

MTU 20V4000GX2, Руководство по эксплуатации

Результаты поиска

Содержание 20V4000GX2

Отзывы:

Похожие инструкции для 20V4000GX2

Бренды по названию

Популярные бренды