MTU 20V4000GX2 Скачать руководство пользователя страница 19

Страница: 19 / 143

Installing the transport locking
device on driving end (KS)

Note:

Install plate (6) on the upper part of the openings only.

Secure the plates (6) with screws (4) and washers (5) at the lateral openings on both sides of the flywheel
housing and tighten to the specified tightening torque.

Name

Size

Type

Lubricant

Value/Standard

Screw

M16

Tightening torque

(Engine oil)

250 Nm +25 Nm

Screw locknut (2) onto screws (1) up to the end of the thread.

The long side of retainer (3) must point downwards. Insert retainer (3) through the openings of plate (6).

Note:

Retainer (3) must lock only the flywheel, not the ring gear.

Screw in screw (1) in bores of retainer (3) until retainer (3) is locked in position.

Note:

Screw (1) must be tightened stepwise and alternately on both sides of the flywheel housing.

Tighten screw (1) to specified tightening torque .

Name

Size

Type

Lubricant

Value/Standard

Screw

M10

Tightening torque

(Engine oil)

30 Nm +3 Nm

Install locknut (2) of screw (1) on plate (6) and tighten.

Removing the transport locking
device from driving end (KS)

Release the locknuts (2) on both sides of the
flywheel housing, remove screw (1) and take
off retainer (3).

Remove screws (4) and take off with wash-
ers (5) and plates (6).

Store the removed parts of the transport
locking device carefully together with this
documentation for possible reuse.

M015565/03E 2016-02

| Transport | 19

TIM-ID: 0000004010 - 015

Содержание 20V4000GX2
















































































































































Результаты поиска

Содержание 20V4000GX2

Отзывы:

Похожие инструкции для 20V4000GX2

Бренды по названию

Популярные бренды

MTU 20V4000GX2, Руководство по эксплуатации

Результаты поиска

Содержание 20V4000GX2

Отзывы:

Похожие инструкции для 20V4000GX2

Бренды по названию

Популярные бренды