MTU 20V4000GX2 Скачать руководство пользователя страница 75

Страница: 75 / 143

8.3 Crankcase Breather

8.3.1 Crankcase breather – Oil separator element replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 4–20 Nm

F30044239

Ratchet adapter

F30027340

Engine oil
Filter element

(→ Spare Parts Catalog)

O-ring

(→ Spare Parts Catalog)

WARNING

Hot oil.
Oil can contain combustion residues which are harmful to health.
Risk of injury and poisoning!
• Wear protective clothing, gloves, and goggles / safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Replacing oil separator filter el-
ement

Use screwdriver to remove securing
screws (2) for cover (1).

Remove cover (1) with O-ring.

M015565/03E 2016-02

| Crankcase Breather | 75

TIM-ID: 0000066941 - 001

Содержание 20V4000GX2
















































































































































Результаты поиска

Содержание 20V4000GX2

Отзывы:

Похожие инструкции для 20V4000GX2

Бренды по названию

Популярные бренды

MTU 20V4000GX2, Руководство по эксплуатации

Результаты поиска

Содержание 20V4000GX2

Отзывы:

Похожие инструкции для 20V4000GX2

Бренды по названию

Популярные бренды