MTS Systems SilentFlo 505G2 Series Скачать руководство пользователя страница 63

Страница: 63 / 94

Maintenance

Series 505G2 SilentFlo™ Hydraulic Power Unit

Prerequisite

You will need a filter element (MTS part number 100-009-495) or a filter kit (MTS part number 100-
030-195).

Procedure

To change the filter element:

Note:

The dirty-filter indicator may light when the HPU is first started due to low hydraulic fluid

temperature. When the HPU is at normal operating temperature, recheck the indicator to
determine if the element actually needs replacement.

1. Turn off the HPU.

2. Open the top of the HPU with an 8-mm (5/16-inch) allen wrench.

Return Line Filter Component Identification

3. Check the output pressure gage. Ensure that the pressure is at zero before proceeding.

4. Unscrew the filter cover. The filter element, bypass assembly, and filter bowl can be removed

as one assembly. Be careful not to spill any hydraulic fluid.

5. Remove the disposable element from the bowl. Discard any fluid contained in the filter bowl.

6. Wipe out any remaining sludge in the filter housing with a lint-free cloth.

7. Inspect the O-rings in the manifold for any sign of deterioration. If necessary, replace the

defective O-ring(s).

8. Insert a new filter element into the bowl and reinstall the bowl assembly. Align the 90° elbow

outlet at the bottom of the assembly such that it directs hydraulic fluid flow towards the side of
the reservoir as shown in the following illustration. Screw the filter cover back on.

Содержание SilentFlo 505G2 Series































































































Результаты поиска

Содержание SilentFlo 505G2 Series

Отзывы:

Похожие инструкции для SilentFlo 505G2 Series

Бренды по названию

Популярные бренды

MTS Systems SilentFlo 505G2 Series, Руководство пользователя

Результаты поиска

Содержание SilentFlo 505G2 Series

Отзывы:

Похожие инструкции для SilentFlo 505G2 Series

Бренды по названию

Популярные бренды