MTS Systems SilentFlo 505G2 Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 94

background image

Operation

56

Series 505G2 SilentFlo™ Hydraulic Power Unit

High pressure

When the Series 505 HPUs are running in high pressure, a considerable amount of heat is generated.
During normal testing, this heat is dissipated by running the hydraulic fluid through the system from the
return line to the heat exchanger. During periods of low system demand, this heat is dissipated by
running the hydraulic fluid through the auto-cooling circuit to the heat exchanger.

Auto-cooling

The Auto-Cooling Valve is adjusted such that the shift between valve closed and valve opened occurs
just below the output pressure level. Whenever system pressure is above the shift level of the Auto-
Cooling Valve (indicating low system demand), the valve opens to port hydraulic fluid through the
return filter to the heat exchanger. When system pressure drops below the shift level (indicating an
increase in system demand), the valve closes and full flow is available to the system.

The effective operating range of the auto-cooling circuit is between system pressures of 14 MPa (2000
psi) to 21 MPa (3000 psi). In order for the Auto-Cooling Valve to function properly, it must be re-
adjusted anytime the output pressure will be changed for longer than 10 minutes.

Note:

If the test condition requires a maximum pressure level less than 14 MPa (2000 psi),

consult MTS.

«
...
54
55
56
57
58
...
»

Содержание SilentFlo 505G2 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для SilentFlo 505G2 Series

Бренд: Balmar Страницы: 20

Бренд: Harbor Freight Tools Страницы: 32

ATS-909X - WORLD BAND RADIOS

Бренд: Sangean Страницы: 1

Бренд: Sangean Страницы: 96

Бренд: Sandstorm Страницы: 208

Бренд: Ford Страницы: 24

Бренд: Akai Страницы: 2

Бренд: SOUNDMASTER Страницы: 73

Бренд: Acterna Страницы: 40

Бренд: Akai Страницы: 20

Бренд: Feider Machines Страницы: 80

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 2

Magnavox AZ 7483

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды