MTS Systems SilentFlo 505G2 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 94

background image

Installation

Series 505G2 SilentFlo™ Hydraulic Power Unit

35

G. Verify the correct output pressure, as shown on the pressure gage.

H. Press the Stop button to shut down the unit.

6. Connect the controller cable (if used).

The controller cable provides a means to connect your controller to the HPU. When
connected, your controller can remotely start and stop the unit and switch between the low
and high pressure selections. The cable also permits the controller to monitor the low level,
overtemperature, and dirty filter status.

Important:

If a controller is not used, the installed jumper plug must be used or the unit

will not start.

Connect the controller cable to the connector located at the lower left side of the electrical
enclosure.

HPU Setup

The following procedure should only be performed at HPU installation to verify settings, when you
replace the user interface panel, or if you need to change a selection.

1. Rotate the power disconnect switch to the on (|) position.

2. On the user interface Main Display, select the language.

3. On the user interface Main screen ensure that the

Remote Operation

button is not selected

(gray), indicating the HPU is in local mode.

4. On the user interface panel, press and hold the

Setup

button for five seconds to display the

«
...
33
34
35
36
37
...
»

Содержание SilentFlo 505G2 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для SilentFlo 505G2 Series

Бренд: Saint Productions Страницы: 16

Бренд: Panasonic Страницы: 7

Бренд: Teac Страницы: 6

Бренд: Generac Power Systems Страницы: 36

Бренд: Hytera Страницы: 33

Бренд: Polaroid Страницы: 29

Бренд: Predator Страницы: 24

Бренд: R&S Страницы: 81

Бренд: Homelite Страницы: 68

Бренд: GPX Страницы: 12

Бренд: LONCIN Страницы: 27

Бренд: Firman Страницы: 57

Бренд: LIFAN Power USA Страницы: 34

Бренд: BG7TBL Страницы: 18

Бренд: Parkside Страницы: 120

VarioMatch Match Network VM 1000 Platform

Бренд: Advanced Energy Страницы: 194

Бренд: GE Страницы: 20

Бренд: GE Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды