MTS Systems SilentFlo 505G2 Series Скачать руководство пользователя страница 42

Страница: 42 / 94

Operation

Series 505G2 SilentFlo™ Hydraulic Power Unit

Name and Location

Description

operation.

Remote Operation - gray: Indicates the HPU is not in remote
operation.

Remote Operation - green: Indicates the HPU is in remote
operation.

In remote operation, the local Run and High Pressure buttons
are disabled

Pump Hours

Indicator/Display: Indicates total running time of the HPU.

Oil Pressure

Part of the Analog
Option;only displayed if the
Analog Option was
purchased.

Indicator/Display: Indicates output pressure of the HPU.

Oil Temp(erature)

Part of the Analog
Option;only displayed if the
Analog Option was
purchased.

Indicator/Display: Indicates the temperature of the hydraulic
fluid in the reservoir.

Oil Level

Part of the Analog
Option;only displayed if the
Analog Option was
purchased.

Indicator/Display: Displays the level of the hydraulic fluid in
the reservoir in 1/8 increments. The level is relative to the
bottom of the sensor, not the bottom of the reservoir.

Содержание SilentFlo 505G2 Series































































































Результаты поиска

Содержание SilentFlo 505G2 Series

Отзывы:

Похожие инструкции для SilentFlo 505G2 Series

Бренды по названию

Популярные бренды

MTS Systems SilentFlo 505G2 Series, Руководство пользователя

Результаты поиска

Содержание SilentFlo 505G2 Series

Отзывы:

Похожие инструкции для SilentFlo 505G2 Series

Бренды по названию

Популярные бренды