background image

MANUFACTURER’S LIMITED WARRANTY FOR:

The limited warranty set forth below is given by MTD LLC with 
respect to new merchandise purchased and used in the 
United States, its possessions and territories.

“MTD”warrants this product against defects in material and 
workmanship for a period of two (2) years commencing on the 
date of original purchase and will, at its option, repair or 
replace, free of charge, any part found to be defective in 
materials or workmanship. This limited warranty shall only 
apply if this product has been operated and maintained in 
accordance with the Operator’s Manual furnished with the 
product, and has not been subject to misuse, abuse, 
commercial use, neglect, accident, improper maintenance, 
alteration, vandalism, theft, fire, water, or damage because of 
other peril or natural disaster. Damage resulting from the 
installation or use of any part, accessory or attachment not 
approved by MTD for use with the product(s) covered by this 
manual will void your warranty as to any resulting damage.

Normal wear parts or components thereof are subject to 
separate terms as follows: All normal wear parts or 
component failures will be covered on the product for a period 
of 90 days regardless of cause. After 90 days, but within the 
two year period, normal wear part failures will be covered 
ONLY IF caused by defects in materials or workmanship of 
OTHER component parts. Normal wear parts and 
components include, but are not limited to: batteries, belts, 
blades, blade adapters, grass bags, rider deck wheels, seats, 
snow thrower skid shoes, shave plates, auger spiral rubber, 
and tires.

HOW TO OBTAIN SERVICE: Warranty service is available, 
WITH PROOF OF PURCHASE, through your local authorized 
service dealer. To locate the dealer in your area, check your 
Yellow Pages, or contact MTD LLC at P.O. Box 361131, 
Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1-
330-220-4683 or log on to our Web site at 
www.mtdproducts.com.

This limited warranty does not provide coverage in the 
following cases:

a.

The engine or component parts thereof. These items 

may carry a separate manufacturer’s warranty. Refer 
to applicable manufacturer’s warranty for terms and 
conditions.

b.

Log splitter pumps, valves, and cylinders have a 

separate one year warranty.

c.

Routine maintenance items such as lubricants, filters, 

blade sharpening, tune-ups, brake adjustments, clutch 
adjustments, deck adjustments, and normal 
deterioration of the exterior finish due to use or 
exposure.

d.

MTD does not extend any warranty for products sold or 

exported outside of the United States, its possessions 
and territories, except those sold through MTD’s 
authorized channels of export distribution.

e.

Replacement parts that are not genuine MTD parts.

f.

Service completed by someone other than an 

authorized service dealer.

g.

Transportation charges and service calls.

No implied warranty, including any implied warranty of 
merchantability of fitness for a particular purpose, 
applies after the applicable period of express written 
warranty above as to the parts as identified. No other 
express warranty, whether written or oral, except as 
mentioned above, given by any person or entity, 
including a dealer or retailer, with respect to any product, 
shall bind MTD. During the period of the warranty, the 
exclusive remedy is repair or replacement of the product 
as set forth above.

The provisions as set forth in this warranty provide the 
sole and exclusive remedy arising from the sale. MTD 
shall not be liable for incidental or consequential loss or 
damage including, without limitation, expenses incurred 
for substitute or replacement lawn care services or for 
rental expenses to temporarily replace a warranted 
product.

Some states do not allow the exclusion or limitation of 
incidental or consequential damages, or limitations on how 
long an implied warranty lasts, so the above exclusions or 
limitations may not apply to you.

In no event shall recovery of any kind be greater than the 
amount of the purchase price of the product sold. Alteration 
of safety features of the product shall void this warranty. 
You assume the risk and liability for loss, damage, or injury to 
you and your property and/or to others and their property 
arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the 
original purchaser or to the person for whom it was purchased 
as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This 
limited warranty gives you specific legal rights, and you may 
also have other rights which vary from state to state.

                       IMPORTANT: Owner must present Original Proof of Purchase to obtain warranty coverage.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683

Содержание 644E

































Отзывы: