MTD 644E Скачать руководство пользователя | Manualshive

Страница: 10 / 32

background image

10

Attaching The Chute Directional Control

(Hardware C)

•

Thread one hex nut about halfway onto eye bolt on
the chute directional control.

•

Insert eye bolt through the hole provided in the left
handle. See Figure 13.

•

Secure with cupped washer (cupped side against
the handle) and other hex nut. Do not tighten until
after attaching the other end of the chute directional
control.

Figure 13

•

To align the spiral on the chute directional control,
you may have to loosen the carriage bolts and hex
lock nuts securing lower chute bracket to the
extension on the left side of the chute assembly.
See Figure 14.

•

Insert the end of the control into the hole in the
plastic bushing in the lower chute bracket.

•

Place the flat washer on the end of the chute
directional control, and insert hairpin clip into hole in
the end of control. See Figure 14.

•

Adjust the chute bracket so that the spiral on the
chute directional control fully engages the teeth on
the chute assembly.

•

Tighten nuts on the lower chute bracket securely.

•

Tighten hex nut on the eye bolt on chute directional
control.

Figure 14

Lamp Wiring

(If Equipped)

NOTE: A lamp is an optional feature of some model
snow throwers and is NOT standard equipment. On
models so equipped, a lamp will either be installed on
the dash panel at the factory OR packaged separately
as a Kit within the carton, depending on the model.

•

If so equipped, wrap the wire from the lamp down
the right handle until the wire can be plugged into
the alternator lead wire located under the fuel tank.
See Figure 15. Lamp wire must not interfere with
any controls or cables.

Figure 15

Eye Bolt

Hex Nut

Cupped
Washer

Lower Chute
Bracket

Hex Lock
Nuts

Carriage
Bolts

Chute

Hairpin

Lower Chute
Bracket

Flat
Washer

Clip

Directional
Control

Lower Handle

Alternator

Lead

Lamp

Wire

«
...
8
9
10
11
12
...
»

Содержание 644E

































Отзывы:

Нет отзывов

Похожие инструкции для 644E

S-HSB183072IN-MP1220

Бренд: LANDY Страницы: 20

Бренд: Remington Страницы: 32

Бренд: Ybravo Страницы: 16

Massey Ferguson Agco Allis 1692934

Бренд: Simplicity Страницы: 21

OPTIMAX LB1401-00-01

Бренд: Little Wonder Страницы: 42

Craftsman 944.525410

Бренд: Sears Страницы: 48

Бренд: Dunsch Страницы: 24

Бренд: Milwaukee Страницы: 4

Бренд: ParkerBrand Страницы: 30

Бренд: Vortice Страницы: 52

VORTICE LINEO Q V0

Бренд: Vortice Страницы: 52

Бренд: Troy-Bilt Страницы: 16

Бренд: Cub Cadet Страницы: 28

Бренд: Snapper Страницы: 24

Бренд: Yard-Man Страницы: 16

Бренд: Vanguard Страницы: 2

POWERPLUS POWXG4060

Бренд: Gardenpro Страницы: 9

Бренд: Land Pride Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды