MTD 644E Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

background image

17

NOTE:

Make certain to check for correct adjustment

of the shift rod as instructed in the Final Adjustments
section before operating the snow thrower.

Drive Wheels

•

The wheels may be adjusted for two different
methods of operation. Follow the steps below for
adjustment. See Figure 22.

Figure 22

One Wheel Driving

•

On the right side of the unit, place click pin in the
outside axle hole only. Do not place pin through
wheel hub.This position gives power drive to the left
wheel only, making the unit easier to maneuver.

Both Wheels Driving

•

Rotate wheel assembly to align hole in the hub with
the inner hole on the axle shaft. Insert click pin in
the hole. Outer axle shaft hole should be visible.

IMPORTANT:

NEVER operate the snow thrower with the

click pin inserted through both the RIM and the
OUTSIDE HOLE in the axle. Doing so can result in
serious damage to the drive system.

SECTION 7: MAINTAINING YOUR SNOW THROWER

WARNING:

Before lubricating, repair-

ing, or inspecting, disengage all clutch
levers and stop engine. Wait until all mov-
ing parts have come to a complete stop.
Disconnect spark plug wire and ground it
against the engine to prevent unintended
starting.

Lubrication

Engine

Refer to the separate engine manual packed with your
unit for all engine lubrication instructions.

WARNING:

If any adjustments need to

be made to the engine while the engine is
running (e.g. carburetor), keep clear of all
moving parts. Be careful of muffler, engine
and other surrounding heated surfaces.

Gear Shaft

•

Lubricate the gear shaft with a good all-weather
multi-purpose light grease at least once a season or
after every 25 hours of operation.

IMPORTANT:

Keep all grease and oil off the friction

wheel and drive plate.

Wheels

•

Oil or spray lubricant into bearings at wheels at
least once a season. Pull click pin, remove wheels,
clean and coat axles with a multipurpose
automotive grease. See Figure 23.

Figure 23

Chute Directional Control

•

The worm gear on the chute directional control
should be greased with multipurpose automotive
grease.

Inside Hole
In Axle

Click Pin In
Outside Hole

Click Pin

Axle

«
...
15
16
17
18
19
...
»

Содержание 644E

































Отзывы:

Нет отзывов

Похожие инструкции для 644E

Бренд: Lamson Страницы: 4

Бренд: Yardworks Страницы: 18

Бренд: Tarmo Страницы: 36

Бренд: Kärcher Страницы: 510

Бренд: ebm-papst Страницы: 11

Бренд: Ross Страницы: 8

Бренд: EarthWise Страницы: 8

4SISON BLAX2-M-EU

Бренд: Sabre Страницы: 48

Бренд: Cub Cadet Страницы: 56

Бренд: Hitachi Koki Страницы: 80

Бренд: Troy-Bilt Страницы: 29

Бренд: MTD Страницы: 32

770-10538 31AH4Q3G100

Бренд: Cub Cadet Страницы: 28

Бренд: Giant-Vac Страницы: 12

72V Li-ION Power 24B

Бренд: Wolf Garten Страницы: 120

Бренд: Milwaukee Страницы: 4

Бренд: LOFTNESS Страницы: 36

Бренд: Desa Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды