MTD 644E Скачать руководство пользователя | Manualshive

Страница: 18 / 32

background image

18

Auger Shaft

•

At least once a season, remove shear bolts on
auger shaft. Oil or spray lubricant inside shaft and
lubricate the auger bearings. See Figure 24.

Figure 24

Drive and Shifting Mechanism

Remove rear cover. Oil any chains, sprockets, gears,
bearings, shafts, and shifting mechanism at least once
a season. Use engine oil or a spray lubricant. Avoid
getting oil on rubber friction wheel and aluminum drive
plate. See Figure 25.

Figure 25

Gear Case

The worm gear case has been filled with grease at the
factory. If disassembled for any reason, lubricate with 2
ounces of shell grease, part number 737-0168.

IMPORTANT:

Do not overfill the gear case. Damage to

the seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.

SECTION 8: SERVICING YOUR SNOW THROWER

WARNING:

Before servicing, repairing,

or inspecting, disengage all clutch levers
and stop engine. Wait until all moving
parts have come to a complete stop.
Disconnect spark plug wire and ground it
against the engine to prevent unintended
starting

Engine

Refer to the separate engine manual packed with your
unit for all engine maintenance procedures.

Shave Plate and Skid Shoes

•

The shave plate and skid shoes on the bottom of
the snow thrower are subject to wear. They should
be checked periodically and replaced when
necessary.

•

To remove skid shoes, remove the four carriage
bolts, cupped washers and hex nuts which attach
them to the snow thrower. Reassemble new skid
shoes with the four carriage bolts, cupped washers
(cupped side goes against skid shoes) and hex
nuts. See Figure 26.

•

To remove shave plate, remove the carriage bolts,
cupped washers and hex nuts which attach it to the
snow thrower housing. Reassemble new shave
plate, making sure heads of carriage bolts are to
the inside of housing. Tighten securely.

Figure 26

Vent Plug

Plastic
Bearing

Plastic
Bearing

Shear Bolts

Chain

Shift Lever

Gear Shaft

Avoid oil on
friction wheel and
drive plate

Carriage

Skid Shoe

Hex Nuts

Shave Plate

Bolts

Skid Shoe

«
...
16
17
18
19
20
...
»

Содержание 644E

































Отзывы:

Нет отзывов

Похожие инструкции для 644E

Бренд: LAWN STAR Страницы: 13

Бренд: Yardworks Страницы: 24

Бренд: Black & Decker Страницы: 6

Бренд: Black & Decker Страницы: 4

Бренд: Black & Decker Страницы: 4

Бренд: Black & Decker Страницы: 4

Бренд: Black & Decker Страницы: 10

Бренд: Black & Decker Страницы: 16

Бренд: Giant-Vac Страницы: 16

Бренд: Toro Страницы: 16

Бренд: Coopers Страницы: 13

Бренд: Toro Страницы: 24

Бренд: F.F. Group Страницы: 24

Бренд: Allied Страницы: 30

Mighty-Vac 80275

Бренд: Balboa Страницы: 2

OmniPro OmniDry 2.9 Amp

Бренд: Hydro-Force Страницы: 5

Бренд: Yardworks Страницы: 23

Бренд: Yard Machines Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды