manualshive.com logo in svg

MTD 31A-610, Руководство пользователя, Страница: 6 / 24

Поделиться
Скачать
MTD 31A-610 Скачать руководство пользователя страница 6

ATTACHING THE HANDLES (Hardware A)

1. Place right handle in position against the

snowthrower so the flat side of the handle

is against the snowthrower. Secure bottom

hole in handle to snowthrower using hex

bolt (B) and lockwasher (C). There are per-

manent nuts on the inside of the frame for

these bolts. See figure 3.

Do not tighten

at this time.

2. Place saddle (I) over upper holes on han-

dles (curve matching curve on handle),

secure to the frame with lockwashers (C)

and hex bolts (A). See figure 3.

Do not

tighten at this time.

3. Attach the left handle in the same manner.

NOTE:

Hex bolts (A) and (B) have a

chemical patch which sets after bolt is

assembled.

6

Pliers
Two ½" Wrenches or adjustable

Two 7/16" Wrenches or adjustable
Two 9/16" Wrenches or adjustable
3/8" Wrench

NOTE:

The snowthrower is shipped with oil and WITHOUT GASOLINE. After assembly, refer to

separate engine manual for proper fuel and engine oil recommendations.

ASSEMBLY INSTRUCTIONS

Reference to right hand or left hand side of machine are observed from the operating position.

FIGURE 3

Saddle (I)

Hex Bolt (A)

1-3/4" Lg.

Lockwasher (C)

Hex Bolt (B)

3/4" Lg.

FIGURE 2 - LOOSE PARTS IN CARTON

"Z" Fitting (in hardware pack)

Clutch Grip RH

Clutch Grip Bracket RH

Handle RH

Handle LH

"Z" Fitting (in

hardware pack)

Clutch

Grip

Bracket

LH

Chute Crank

Shift Rod

Chute

Assembly

Shift Lever

Control Panel

Clutch Grip LH

Содержание 31A-610

























Отзывы:

Нет отзывов