manualshive.com logo in svg

MTD 31A-610, Руководство пользователя, Страница: 11 / 24

Поделиться
Скачать
MTD 31A-610 Скачать руководство пользователя страница 11

2. Make certain the auger and drive clutch le-

vers are in the disengaged (released)

position.

3. Move throttle control up to FAST

posi-

tion. Insert ignition key into slot. See figure

14. Be certain it snaps into place. Do not

turn key.

4. Rotate choke knob to ON position.
5. Connect power cord to switch box on en-

gine. Plug the other end of power cord into

a three-hole, grounded 120 volt AC recep-

tacle.

6. Push starter button to crank engine. See

figure 14. As you crank the engine, move

choke knob to FULL choke

position.

7. When engine starts, release starter button,

and move choke gradually to OFF

. If

engine falters, move choke immediately to

FULL and then gradually to OFF.

Recoil Starter:

1. Make certain the metal loop on the end of

the spark plug wire (inside the boot) is fas-

tened securely over the metal tip on the

spark plug. See figure 13.

2. Make certain the auger and drive clutch le-

vers are in the disengaged (released)

position.

3. Move throttle control up to FAST

posi-

tion. Insert ignition key into slot. See figure

14. Be certain it snaps into place. Do not

turn key.

4. Rotate choke knob to FULL choke position

(cold engine start).

If engine is warm, place choke in OFF

position instead of FULL.

5. Push primer button two or three times. See

figure 14.

If engine is warm, push primer button

once only.

NOTE: Always cover vent hole in

primer button when pushing. Addi-

tional priming may be necessary for

first start if temperature is below 15°F.

6. Grasp starter handle (see figure 14) and

pull rope out slowly, until it pulls slightly

harder. Let rope rewind slowly.

7. Pull starter handle rapidly. Do not allow

handle to snap back. Allow it to rewind

slowly while keeping a firm hold on the

starter handle. Repeat until engine starts.

9. As engine warms up and begins to operate

evenly, rotate choke knob slowly to OFF

position. If engine falters, return to FULL

choke, then slowly move to OFF position.

TO STOP ENGINE

1. Run engine for a few minutes before stop-

ping to help dry off any moisture on the

engine.

2. To help prevent possible freeze-up of

starter, proceed as follows.

Optional Electric Starter: Connect power

cord to switch box on engine, then to 120

volt AC receptacle. With the engine run-

ning, push starter button and spin the

starter for several seconds. The unusual

sound made by spinning the starter will

not harm engine or starter. Disconnect

the power cord from receptacle first, and

then from switch box.
Recoil Starter: With engine running, pull

starter rope with a rapid, continuous full

arm stroke three or four times. Pulling the

starter rope will produce a loud clattering

sound, which is not harmful to the engine

or starter.

3. To stop engine, remove the ignition key. Do

not turn key. Disconnect the spark plug

wire from the spark plug to prevent acci-

dental starting while equipment is

unattended.

NOTE: Do not lose ignition key. Keep

it in a safe place. Engine will not start

without the ignition key.

4. Wipe all snow and moisture from the carbu-

retor cover in the area of the control levers.

Also, move control levers back and forth

several times.

11

FIGURE 14

Primer

Muffler

Switch Box

Spark Plug

Starter

Button

Ignition

Key

Throttle

Control

Rope Starter

Handle

Содержание 31A-610

























Отзывы:

Нет отзывов