MSC Technologies Avnet COM Express CXC-BT Скачать руководство пользователя страница 60

Страница: 60 / 84

MSC CXC-BT

User Manual

60 / 84

6.4.1 Flat Panel Configuration

Feature

Options

Description

eDP Color Depth

18bit, 24bit

eDP color depth selection. Adjust this according to
the connected eDP display.

When using LVDS, keep this setting consistent with
the selected LVDS Mapping color depth.

NOTE

: This setting is only valid if legacy video bios

is active!

LVDS Panel Type

VBIOS Default
640x480
800x480
800x600
1024x768
1280x720
1280x800
1280x1024
1366x768
1440x900
1600x900
1920x1080
1920x1200

Selected panel type is used if valid EDID data
cannot be found in external Eeprom or non-volatile
BIOS NVRAM.

If None is selected, LVDS controller is disabled.

LVDS Mapping

18bit
24bit LDI
24bit FPDI

Select LVDS mapping type

LVDS Spread Spectrum Disabled, +-

0,25% to +-
1,75% in 0,25%
steps

Configure the spread spectrum for the LVDS
interface.

Number of LVDS
channels

Single Channel
(1bpp)
Dual Channel
(2bpp)

Select number of pixels transferred per clock

Backlight Control

Submenu

Set Backlight settings

6.4.1.1 Backlight Control

Feature

Options

Description

Backlight_EN Control

Chipset, Always
Off

Configures the backlight enable signal. This signal
can either be controlled by chipset, or switched off.

Backlight_EN Polarity

Active

Low,

Active High

Define the polarity of the backlight enable signal.

PWM Control

EC, Chipset

EC means PWM will be controlled by the board
controller. Chipset means PWM will be controlled by
videobios.

Содержание Avnet COM Express CXC-BT





















































































Результаты поиска

Содержание Avnet COM Express CXC-BT

Отзывы:

Похожие инструкции для Avnet COM Express CXC-BT

Бренды по названию

Популярные бренды

MSC Technologies Avnet COM Express CXC-BT, Руководство пользователя

Результаты поиска

Содержание Avnet COM Express CXC-BT

Отзывы:

Похожие инструкции для Avnet COM Express CXC-BT

Бренды по названию

Популярные бренды