mr. steam 104480, Инструкция по установке, эксплуатации и обслуживанию

Страница: 11 / 37

10
Installation & Operating Instructions
®
Maintenance Instructions
Technical Speci fi cations:
Wireless Receiver Unit
Temperature operating -20 C ~ +50 C
Temperature storage -40 C ~ +85 C
Humidity 90%RH non-condensing
Usage type Indoor
Dimensions 41.5 x 117.5 x 22.5 mm (1.625 x 4.875 x 0.875 in.)
Operating frequencies 865 ~ 868 MHz (European Version)
910 ~ 920 MHz (North American Version)
Operating voltage 5.0 V (provided by Steam Generator Unit)
AirTempo Control Unit
Temperature operating -20 C ~ +60 C
Temperature storage -30 C ~ +60 C (limited by battery & LCD)
Humidity 100%RH condensing (external surface only)
IP Rating IPX5
Usage type Indoor
Dimensions 90.0 x 90.0 x 19.0 mm (without decorative bezel)
(3.625 x 3.625 x 0.75 in.)
Operating frequencies 865 ~ 868 MHz (European Version)
910 ~ 920 MHz (North American Version)
Operating voltage 3.0 V
Battery Type CR2450 Primary Manganese Dioxide
Lithium Batteries
(replace only with battery UL1642 approved)
Parts List:
Item # Description Used on
104554BK Electronic Assembly Black All
104554WH Electronic Assembly White All
104209 Retention Ring Flush Mount
(AirTempo Flush)
104210 Flush Mount Box Flush Mount
(AirTempo Flush)
104211 Surface Mount Holder Surface Mount
(AirTempo Surface)
104557 Wireless Receiver All
104213XX Round Bezel Flush Mount
(AirTempo Flush) (specify finish)
104214XX Square Bezel Flush Mount
(specify finish)
104215XX Surface Bezel Surface Mount
(AirTempo Surface) (specify finish)
104220 AirTempo Control Cable (3ft) All
104117-30 30 ft Control Cable Optional
103990-60 60 ft Control Cable Optional
MSTS 30 ft temperature probe Optional
MSTS-60 60 ft temperature probe Optional
Flush Mount AirTempo
U ,i“œÛiÊÌ iÊÃÕÀv>ViʓœÕ˜ÌÊL>ޜ˜iÌÊvÀœ“ÊÌ iÊL>VŽÊœvÊÌ iʈÀ/i“«œÊVœ˜ÌÀœ°
/ iÊÃÕÀv>ViʓœÕ˜ÌÊL>ޜ˜iÌʈÃʘœÌÊÕÃi`ÊÜ i˜ÊyÕà ʓœÕ˜Ìˆ˜}°Ê/ iÊÃÕÀv>Vi
“œÕ˜ÌÊ`iVœÀ>̈ÛiÊLiâiÊˆÃʘœÌÊÕÃi`ÊÜ i˜ÊyÕà ʓœÕ˜Ìˆ˜}°
U 1Ș}ÊÌ iÊÌi“«>ÌiÊ«ÀœÛˆ`i`ʜ˜Ê«>}iÊÓÎ]ÊVÕÌÊÌ iÊ œiʈ˜ÊÌ iÊ`iÈÀi`ʏœV>̈œ˜°
Do not oversize or undersize the cutout. Ensure the template
is level before cutting the hole.
U /iÃÌÊwÌÊÌ iÊyÕà ʓœÕ˜ÌÊLœÝÊ̜Êi˜ÃÕÀiÊÌ iÊ œiʈÃÊÌ iÊVœÀÀiVÌÊÈâi°
U ˜ÃÕÀiÊÌ iʓœÕ˜Ìˆ˜}ÊÃÕÀv>ViʈÃÊVi>˜Ê>˜`Ê`ÀÞ
U ««ÞÊ>ÊÌ ˆ˜ÊLi>`ʜvÊȏˆVœ˜iʈ˜ÊÌ iʏœV>̈œ˜Êà œÜ˜Ê>ÃÊÀiµÕˆÀi`Ê̜ÊVÀi>ÌiÊ>
moisture seal. Remove and discard the release paper to expose the adhesive
liner.
NOTE: The silicone supplied by MrSteam can be used for sealing and
gasketing. It cures to silicone rubber and adheres to glass, wood, metal,
porcelain, ceramic tile, painted surfaces, many plastics and rubber. Surfaces
must be clean and dry. Apply thin layer of product. Fit together and support if
necessary. Allow excess material to cure, then trim with a sharp blade. Sealant
“skins” in 5 minutes, dries to touch in 1 hour. Fully cures and bonds in 24 hrs.
Magnet
Do not apply excessive amounts of sil-
icone. Do not apply silicone to any other parts of the
control including the adhesive gasket. Place the flush
mount box into the hole.
The magnet in the flush mount box
should be orientated at the bottom of the box when
installed.
Flush mount components are sold separately (104232RD &
104232SQ). Contact a MrSteam representative if a flush mount kit is needed.