mr. steam 104480, Инструкция по установке, эксплуатации и обслуживанию

Страница: 9 / 37

8
®
Operating Instructions
Maintenance Instructions
Replace the battery door and lock in place.
To prevent water from getting in the control, ensure the
battery doors are in the locked position before reinstalling control.
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to the instructions.
Battery Replacement
The batteries in AirTempo will need periodic replacement. Both batteries
should be replaced at the same time with new CR2450 coin cell batteries.
CHOKE HAZARD. The batteries and battery doors are
small pieces, keep out of reach of children.
KEEP BATTERIES OUT OF REACH OF CHILDREN.
Swallowing may lead to serious injury or death in as little as 2 hours due
to chemical burns and potential perforation of the esophagus. Immedi-
ately see a doctor.
Remove the AirTempo from the wall by sliding it up and off the bayonet holder.
/ iʈÀ/i“«œÊVœ“iÃʜvvÊÌ iÊyÕà ʓœÕ˜ÌÊ œ`iÀÊLÞÊ}À>눘}ÊÌ iÊLiâiÊ>˜`ʫՏ -
ˆ˜}ÊÌ iÊ>ÃÃi“LÞÊÃÌÀ>ˆ} ÌʜÕÌʜvÊÌ iÊyÕà ʓœÕ˜ÌÊLœÝ°
Use a soft cloth to dry off the control.
With two fingers turn the battery doors in the direction noted. The left battery
cover is opened by turning it clockwise, the right cover is opened by turning it
counterclockwise.
Discard both batteries and replace with new batteries, the positive side of the
battery goes towards the “+” symbol on the battery door.
WARNING
!
WARNING
!
CAUTION
!
CAUTION
!
System Status Codes
The AirTempo
®
may display a status code if the steam system is not
functioning correctly. When batteries are first installed in the control,
it will briefly display r followed by a number. This is the software
revision.
CO indicates the AirTempo
®
control has lost communication with the
steam generator. Ensure all connections are secure between the
steam generator and the transceiver.
Err P indicates an error while pairing, reset the control and redo pairing.
A complete list of steam generator status codes can be found in the
MrSteam Residential Steambath Installation Operation and
Maintenance Manual.
Prr1/2 Indicates are error with the internal (or MSTS) temperature
probe.
Err1 The incorrect field voltage is being supplied to the steam
generator (green LED on steam generator will be off).
H20/Errb: Steam generator water level is not satisfied.
Refer to the steam generator installation, operation and maintenance
manual for trouble shooting.
Pairing
AirTempos are factory paired, however if more than one
steam system is installed in close proximity the AirTempo
®
controls must be paired to their wireless receiver to prevent
interference.
To pair AirTempo
®
use a blunt object to press the button in-
side the wireless receiver adjacent to the LED. Hold the but-
ton for 5 seconds, when the wireless receiver is in pairing
mode the LED will turn blink blue for 2 minutes.
While the transceiver LED is blinking, press and hold the
button on AirTempo ®
for until the display reads PAIR.
Care Tips for AirTempo
®
Controls and Steamheads
1. Use only mild soap and water on a soft cloth to clean the
control and steamhead.
2. Do not use abrasive cleansers
3. If the decorative cover is damaged call MrSteam technical
service for replacement parts.
Warranty
To register your steam generator unit online and to review the
MrSteam Limited Lifetime Warranty please go to:
blog.mrsteam.com/wr