MQ Power DCA125SSIU4F Скачать руководство пользователя страница 9

Страница: 9 / 60

DCA125SSIU4F 60 HZ GENERATOR• OPERATION MANUAL — REV. #0 (07/20/17) — PAGE 9

SAFETY INFORMATION

Grounding Safety

DANGER

This generator is equipped with a grounding terminal

attached to the enclosure. Electrical grounding

requirements can differ by State, Province, District,

Municipality, and unique application settings.

For portable and vehicle-mounted generators, Multiquip

recognizes the guidance provided in NEC Handbook

Article 250.34 Parts A and B, and 29 CFR 1926.404

(f) (3) (i). If a more defi nitive earth-to-ground safeguard

is required, please consult a qualifi ed electrician and

reference appropriate National Electrical Code (NEC)

guidelines in establishing an exterior grounding point

generator.

NEVER

use gas piping as an electrical ground.

NOTICE

There is a permanent conductor

bond

between

generator (stator winding) and the frame.

BATTERY SAFETY

DANGER

DO NOT

drop the battery. There is a possibility that the

battery will explode.

DO NOT

expose the battery to open fl ames,

sparks, cigarettes, etc. The battery contains

combustible gases and liquids. If these

gases and liquids come into contact with a

fl ame or spark, an explosion could occur.

WARNING

ALWAYS

wear safety glasses when

handling the battery to avoid eye irritation.

The battery contains acids that can cause

injury to the eyes and skin.

Use well-insulated gloves when picking up the battery.

ALWAYS

keep the battery charged. If the battery is not

charged, combustible gas will build up.

ALWAYS

recharge the battery in a well-ventilated

environment to avoid the risk of a dangerous concentration

of combustible gasses.

If the battery liquid (dilute sulfuric acid) comes into

contact with

clothing or skin

, rinse skin or clothing

immediately with plenty of water.

If the battery liquid (dilute sulfuric acid) comes into

contact with

eyes

, rinse eyes immediately with plenty

of water and contact the nearest doctor or hospital to

seek medical attention.

CAUTION

ALWAYS

disconnect the

NEGATIVE battery terminal

before performing service on the generator.

ALWAYS

keep battery cables in good working condition.

Repair or replace all worn cables.

Содержание DCA125SSIU4F





























































Результаты поиска

Содержание DCA125SSIU4F

Отзывы:

Похожие инструкции для DCA125SSIU4F

Бренды по названию

Популярные бренды

MQ Power DCA125SSIU4F, Инструкция по эксплуатации

Результаты поиска

Содержание DCA125SSIU4F

Отзывы:

Похожие инструкции для DCA125SSIU4F

Бренды по названию

Популярные бренды