MQ Power DCA125SSIU4F Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 60

background image

DCA125SSIU4F 60 HZ GENERATOR• OPERATION MANUAL — REV. #0 (07/20/17) — PAGE 43

MAINTENANCE

5. Tighten water cock and replace the overflow tank.
6. Place the coolant drain valve in the

CLOSED

position.

7. Replace with coolant as recommended by the engine

manufacturer.

8. Reinstall radiator cap. Tighten securely.

RADIATOR CLEANING

The radiator (Figure 65) should be sprayed (cleaned) with

a high pressure washer when excessive amounts of dirt

and debris have accumulated on the cooling fins or tube.

When using a high pressure washer, stand at least 5 feet

(1.5 meters) away from the radiator to prevent damage to

the fins and tube.

Figure 65. Radiator Cleaning

GENERATOR STORAGE

For long term storage of the generator the following is

recommended:

Drain the fuel tank completely. Treat with a fuel stabilizer

if necessary.

Completely drain the oil from the crankcase and refill if

necessary with fresh oil.

Clean the entire generator, internal and external.

Cover the generating set and store in a clean, dry place.

Disconnect the battery.

Make sure engine coolant is at proper level.

If generator is mounted on a trailer, jack trailer up and

place on blocks so tires do not touch the ground or block

and completely remove the tires.

«
...
41
42
43
44
45
...
»

Содержание DCA125SSIU4F





























































Отзывы:

Нет отзывов

Похожие инструкции для DCA125SSIU4F

SUNNY TRIPOWER STP 20000TL-30

Бренд: SMA Solar Technology Страницы: 50

Бренд: Walter Страницы: 216

Бренд: Fronius Страницы: 190

Бренд: Audio Technica Страницы: 11

Бренд: Growatt Страницы: 25

Бренд: Baumer Страницы: 41

Бренд: Barco Страницы: 4

Autotransformer MW 1700

Бренд: Fronius Страницы: 15

ECO Inverter+ 7

Бренд: Oilon Страницы: 58

SINEMASTER IG4300

Бренд: Kipor Страницы: 50

Бренд: Tascam Страницы: 28

Бренд: TR-Electronic Страницы: 37

Atlona AT-HDVS-SC-RX

Бренд: Panduit Страницы: 41

Бренд: Mayty Страницы: 14

Extron Electonics YCV 100

Бренд: CAMBOARD Страницы: 12

Бренд: Claind Страницы: 35

Бренд: Danfoss Страницы: 33

Бренд: TECO Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды