MQ Power DCA125SSIU4F Скачать руководство пользователя страница 31

Страница: 31 / 60

DCA125SSIU4F 60 HZ GENERATOR• OPERATION MANUAL — REV. #0 (07/20/17) — PAGE 31

Cleaning the Radiator

The engine may overheat if the radiator fins become

overloaded with dust or debris. Periodically clean the

radiator fins with compressed air. Cleaning inside the

machine is dangerous, so clean only with the engine turned

off and the

negative

battery terminal disconnected.

AIR CLEANER

Periodic cleaning/replacement is necessary. Inspect air

cleaner in accordance with the

Isuzu Engine Owner’s

Manual

FAN BELT TENSION

A slack fan belt may contribute to overheating, or to

insufficient charging of the battery. Inspect the fan belt for

damage and wear and adjust it in accordance with the

Isuzu Engine Owner’s Manual.

Fan belt tension is proper if the fan belt bends as

represented in Figure 35 when depressed with the thumb

as shown below. Adjust fan belt tension as required

Figure 35. Fan Belt Tension

0.2 ~ 0.3 IN.

(6 ~ 8 MM)

DEFLECTION

Table 14. Fan Belt Deflection

Belt

Standard Value

Amt. of Deflection

Standard Value

(Vibration Frequency)

New

0.2~0.3 in.

(6~8 mm)

210 Hz.

BATTERY

This unit is of negative ground

DO NOT

connect in reverse.

Always maintain battery fluid level between the specified

marks. Battery life will be shortened, if the fluid level are

not properly maintained. Add only distilled water when

replenishment is necessary.

DO NOT

over fill. Check to see whether the battery

cables are loose. Poor contact may result in poor starting

or malfunctions.

Always

keep the terminals firmly

tightened. Coating the terminals with an approved battery

terminal treatment compound. Replace battery with only

recommended type battery. The battery type used in this

generator is BCI Group 4D.
The battery is sufficiently charged if the specific gravity

of the battery fluid is 1.28 (at 68° F). If the specific gravity

should fall to 1.245 or lower, it indicates that the battery is

dead and needs to be recharged or replaced.
Before charging the battery with an external electric source,

be sure to disconnect the battery cables.

CAUTION

NEVER

place hands near the belts or fan

while the generator set is running.

INSPECTION/SETUP

Содержание DCA125SSIU4F





























































Результаты поиска

Содержание DCA125SSIU4F

Отзывы:

Похожие инструкции для DCA125SSIU4F

Бренды по названию

Популярные бренды

MQ Power DCA125SSIU4F, Инструкция по эксплуатации

Результаты поиска

Содержание DCA125SSIU4F

Отзывы:

Похожие инструкции для DCA125SSIU4F

Бренды по названию

Популярные бренды