MQ Power DCA125SSIU4F Скачать руководство пользователя страница 32

Страница: 32 / 60

PAGE 32 — DCA12SSIU4F 60 HZ GENERATOR • OPERATION MANUAL — REV. #0 (07/20/17)

Battery Cable Installation

ALWAYS

be sure the battery cables (Figure 36) are

properly connected to the battery terminals as shown below.

The

red cable

is connected to the positive terminal of the

battery, and the

black cable

is connected to the negative

terminal of the battery.

Figure 36. Battery Connections

When connecting battery do the following:
1.

NEVER

connect the battery cables to the battery

terminals when the

Auto-Off/Reset-Manual Switch

is in either the

AUTO

MANUAL

position.

ALWAYS

make sure that this switch is in the

OFF/RESET

position when connecting the battery.

2. Place a small amount of battery terminal treatment

compound around both battery terminals. This will

ensure a good connection and will help prevent

corrosion around the battery terminals.

CAUTION

ALWAYS

disconnect the negative terminal

FIRST

and

reconnect negative terminal

LAST

POSITIVE

NEGATIVE

NOTICE

If the battery cable is connected incorrectly, electrical

damage to the generator will occur. Pay close attention

to the polarity of the battery when connecting the battery.

CAUTION

Inadequate battery connections may cause poor

starting of the generator, and create other malfunctions.

ALTERNATOR

The polarity of the alternator is negative grounding type.

When an inverted circuit connection takes place, the

circuit will be in short circuit instantaneously resulting the

alternator failure.

DO NOT

put water directly on the alternator. Entry of water

into the alternator can cause corrosion and damage the

alternator.

WIRING

Inspect the entire generator for bad or worn electrical wiring

or connections. If any wiring or connections are exposed

(insulation missing) replace wiring immediately.

PIPING AND HOSE CONNECTION

Inspect all piping, oil hose, and fuel hose connections for

wear and tightness. Tighten all hose clamps and check

hoses for leaks.
If any hose (

fuel or oil

) lines are defective replace them

immediately.

INSPECTION/SETUP

Содержание DCA125SSIU4F





























































Результаты поиска

Содержание DCA125SSIU4F

Отзывы:

Похожие инструкции для DCA125SSIU4F

Бренды по названию

Популярные бренды

MQ Power DCA125SSIU4F, Инструкция по эксплуатации

Результаты поиска

Содержание DCA125SSIU4F

Отзывы:

Похожие инструкции для DCA125SSIU4F

Бренды по названию

Популярные бренды