Moxa Technologies EDS-405A Скачать руководство пользователя страница 81

Страница: 81 / 103

EDS-405A/408A Series User’s Manual

Featured Functions

3-66

Using Syslog

This function provides the event logs for the syslog server. The function supports 3 configurable
syslog servers and syslog server UDP port numbers. When an event occurs, the event will be sent
as a syslog UDP packet to the specified syslog servers.

Syslog Server 1

Setting

Description

Factory Default

IP Address

Enter the IP address of 1st Syslog Server used by
your network.

None

Port Destination
(1 to 65535)

Enter the UDP port of 1st Syslog Server.

514

Syslog Server 2

Setting

Description

Factory Default

IP Address

Enter the IP address of 2nd Syslog Server used by
your network.

None

Port Destination
(1 to 65535)

Enter the UDP port of 2nd Syslog Server.

514

Syslog Server 3

Setting

Description

Factory Default

IP Address

Enter the IP address of 3rd Syslog Server used by
your network.

None

Port Destination
(1 to 65535)

Enter the UDP port of 3rd Syslog Server.

514

NOTE

The following events will be recorded into the EDS-405A/408A’s Event Log table, and will then
be sent to the specified Syslog Server:
1.

Cold start

Warm start

Configuration change activated

Power 1/2 transition (Off



On), Power 1/2 transition (On



Off)

Authentication fail

Topology changed

Master setting is mismatched

DI 1/2 transition (Off



On), DI 1/2 transition (On



Off)

Port traffic overload

10.

dot1x Auth Fail

11.

Port link off / on

Содержание EDS-405A








































































































Результаты поиска

Содержание EDS-405A

Отзывы:

Moxa Technologies EDS-405A, Руководство пользователя, Страница: 81 / 103

Результаты поиска

Содержание EDS-405A

Отзывы: