Moxa Technologies airworks awk-5232 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 81

background image

AWK-5232

Supporting Information

7-2

About This User’s Manual

This manual is mainly designed for, but no limited to, the following hardware and firmware for the AWK-5232:

•

Hardware Rev: 1.0

•

Firmware Ver: 1.0

You are strongly recommended to visit Moxa’s website (http://www.moxa.com) and find the latest product
datasheet, firmware, QIG (Quick Installation Guide), UM (User’s Manual) and related information.

NOTE

You can find out the hardware revision number of AWK-5232 on the side label.

The firmware version number can be seen on the Overview page, as follow:

DoC (Declaration of Conformity)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example – use only shielded interface cables when connecting
to computer or peripheral devices). Any changes or modifications not expressly approved by the party

«
...
76
77
78
79
80
...
»

Содержание airworks awk-5232


















































































Отзывы:

Нет отзывов

Похожие инструкции для airworks awk-5232

Бренд: 4RF Страницы: 7

UP Squared 6000 Edge Computing Kit

Бренд: Aaeon Страницы: 59

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

SR8800 IM-FW-II

Бренд: H3C Страницы: 107

Бренд: 3Com Страницы: 12

Бренд: H3C Страницы: 16

H3C S3600 Series

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 2

H3C S7500E Series

Бренд: H3C Страницы: 34

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 14

Бренд: H3C Страницы: 56

H3C S7500E Series

Бренд: H3C Страницы: 112

Бренд: H3C Страницы: 15

SR8800 IM-FW-II

Бренд: H3C Страницы: 5

H3C S7500E Series

Бренд: H3C Страницы: 50

Бренд: H3C Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды