Moxa Technologies airworks awk-5232 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 81

background image

AWK-5232

Web Console Configuration

3-21

Fragmentation threshold

Setting

Description

Factory Default

Fragment Length
(256 to 2346)

Specifies the maximum size a data packet before splitting and
creating another new packet

2346

RTS threshold

Setting

Description

Factory Default

RTS/CTS Threshold
(256 to 2346)

Determines how large a packet can be before the Access Point
coordinates transmission and reception to ensure efficient
communication

2346

NOTE

You can refer to the related glossaries in Chapter 5 for detailed information about the above-mentioned
settings. By setting these parameters properly, you can better tune the performance of your wireless network.

Noise protection

Setting

Description

Factory Default

Enable/Disable

Adjusts the interference coping capability of the wireless signal.
This option should be enabled for communication distance
under 500 meters, and should be disabled for communication
distances over 500 meters.

Enable

Transmission enhancement

Setting

Description

Factory Default

Enable/Disable

This setting can enhance communication by strengthening the
AWK-5232’s transmission power. It is quite useful for
long-distance transmission or countering environmental
interference. The user must carefully evaluate and measure the
transmission power of the entire system to ensure it stays
below the regulative limit. In addition, that RF type 802.11a
mode cannot be used if this function is enabled.

Disable

NOTE

Make sure the same Transmission distance parameters are set in both AP and Client. When this parameter
is greater than 500, an optimal algorithm will be enabled to support long-distance transmission.
Note that Transmission enhancement only supports 802.11b/g/n mode; 802.11a mode is not supported.
Transmission enhancement is also recommended to enable communication at both ends when
long-distance transmission is required. A high-gain antenna installed at a fixed antenna connector can also
improve performance.

EAPOL Version

Setting

Description

Factory Default

1

EAPOL version 1 was standardized in the 2001 version of
802.1X, which is much more commonly implemented.

1

2

EAPOL version 2 was specified in 802.1X-2004.

WMM

Setting

Description

Factory Default

Enable/Disable

WMM is a QoS standard for WLAN traffic. Voice and video data
will be given priority bandwidth when enabled with WMM
supported wireless clients.

Note: WMM will always be enabled under 802.11n mode.

Enable

Full 11a channel support

Setting

Description

Factory Default

Enable/Disable

Enabling this option allows users to select 5GHz channels from
both licensed and unlicensed bands.

Disable

«
...
33
34
35
36
37
...
»

Содержание airworks awk-5232


















































































Отзывы:

Нет отзывов

Похожие инструкции для airworks awk-5232

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: H3C Страницы: 6

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 4

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 60

Бренд: H3C Страницы: 149

Бренд: 3Com Страницы: 27

Бренд: SAF Страницы: 30

neutrino series

Бренд: Xilica Audio Design Страницы: 26

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: Ebyte Страницы: 14

Бренд: IBM Страницы: 63

Бренд: Watchguard Страницы: 40

Teranex 2D Processor

Бренд: Blackmagicdesign Страницы: 969

Бренд: CNC4PC Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды