Moxa Technologies airworks awk-5232 Скачать руководство пользователя страница 38

Страница: 38 / 81

AWK-5232

Web Console Configuration

3-24

Configuring Virtual LAN

VLAN Settings

To configure the AWK’s VLAN, use the VLAN Setting page to configure the ports.

Management VLAN ID

Setting

Description

Factory Default

VLAN ID
ranges from
1 to 4094

Set the management VLAN of this AWK.

Port

Type

Description

Trunk Port

LAN

This port is the LAN port on the AWK.

Yes

WLAN

This is a wireless port for the specific SSID. This field will refer to
the SSID that you have created. If more SSIDs have been
created, new rows will be added.

Port PVID

Setting

Description

Factory Default

VLAN ID ranging from 1
to 4094

Set the port’s VLAN ID for devices that connect to the port. The
port can be a LAN port or WLAN ports.

VLAN Tagged

Setting

Description

Factory Default

A comma-seperated list
of VLAN IDs. Each of
the VLAN IDs range
from 1 to 4094.

Specify which VLANs can communicate with this specific VLAN. (Empty)

Содержание airworks awk-5232

















































































Результаты поиска

Содержание airworks awk-5232

Отзывы:

Похожие инструкции для airworks awk-5232

Бренды по названию

Популярные бренды

Moxa Technologies airworks awk-5232, Руководство пользователя

Результаты поиска

Содержание airworks awk-5232

Отзывы:

Похожие инструкции для airworks awk-5232

Бренды по названию

Популярные бренды