Mouvex C12 A Скачать руководство пользователя страница 17

Страница: 17 / 20

11.1 Replacement of the jacket seal

• Remove the 4 screws

132

from the main body

101

well as the main body plate

131

and the seal

130

• Reassembly is in reverse order of disassembly.

11.2 Bleed (included with jacket option)

• A bleed is provided on the main body

101

and the front

cover

401

(only in position 2 or 4 for the front cover -

see board "Possible positions " § INSTALLATION).

• Using an Allen key, unscrew the screws

122

• Check the state of the seal

121

, replace it if necessary.

• Reassembly is in reverse order of disassembly.

WARNING

Hazardous pressure

can cause

personal injury

or property damage.

DISCONNECTING THE FLUID OR PRESSU-
RE CONTAINMENT COMPONENTS
DURING PUMP OPERATION CAN CAUSE
SERIOUS PERSONAL INJURY, DEATH OR
MAJOR PROPERTY DAMAGE.

Before carrying out any work, make sure
that no fluid flows in the casing (heating /
cooling circuit valve closed) and that the
pump is at ambient temperature.

11. HEATING JACKET (option)

17/20

NT 1001-F00 10.10 C12 A - C18 A e

Содержание C12 A





















Результаты поиска

Содержание C12 A

Отзывы:

Похожие инструкции для C12 A

Бренды по названию

Популярные бренды

Mouvex C12 A, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание C12 A

Отзывы:

Похожие инструкции для C12 A

Бренды по названию

Популярные бренды