Mountfield 2105M, Инструкция по эксплуатации, Страница: 8 / 44

8
ENGLISH EN
3 ASSEMBLY
To avoid injury and damage to people
and property, do not use the machine
until all the measures under “ASSEM-
BLY” have been carried out.
3.1 Assembly components
Components that are to be used at assembly are in-
cluded in the delivery. See fig. 1.
Supplied in bag:
Pos No. Designation Dimension
A 1 Towing plate
B 2 Screw with flange 8 x 20
C 2 Screw for battery
D 2 Nut for battery
E 4 Washer 8.4 x 24 x 2.0
F 2 Shoulder washer
G 4 Screw 8 x 20
I 2 Ignition key
J 1 Tension pin 6 x 36
K 1 Shim washer 16 x 38 x 0.5
L 1 Shim washer 16 x 38 x 1.0
P 2 Screw M10 x 35
Q 2 Nut M10
Supplied installed on the front axles:
Pos No. Designation
M
2 Circlip
N 2 Washer with internal lug
Secured to the implement lifter:
Pos No. Designation
O
2 Deck mount
3.2 ENGINE CASING
To fill with fuel and to inspect and maintain the en-
gine and battery, open the engine casing.
The engine must not be running when
the casing is opened.
3.2.1 Opening
1. Ensure that the control arms are in their forward
positions.
2. Raise the seat lock (2:S) and fold the seat for-
wards.
3. Grasp the front edge of the engine casing and
fold up the casing (fig. 3).
3.2.2 Closing
Grasp the front edge of the engine casing and fold
down the casing (fig. 3).
The machine may not be operated un-
less the engine casing is folded down.
Risk of burns and crushing injuries.
3.3 Battery
See “8.8 Battery”.
3.4 Seat
Release the catch (2:S) and fold up the seat brack-
et.
Install the mounting in the rear (upper) holes as
follows:
1. Install the shoulder washers (2:F) on the screws
(2:G).
2. Insert the screws through the slots in the brack-
et. Place a washer (2:I) between the seat and the
bracket.
3. Tighten the screws in the seat. Tightening
torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
4. Check that the seat moves easily in the slots in
the bracket.
Install the mounting in the front (lower) holes as
follows:
1. Install the screw knobs (2:H) on the screws
(2:G).
2. Install a washer (2:I) on each screw.
3. Insert the screws through the slots in the bracket
and tighten by hand in the seat.
4. Fold the seat down and place it in the desired
position.
5. Tighten the screw knobs (2:H) by hand.
The screw knobs (2:H) and the seat will
be damaged if tools are used.
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
The seat is locked. To fold the seat up or down, re-
lease the catch (2:S).
3.5 Steering wheel
In order to minimise the axial play in the steering
column, the shim washers (4:D) and/or (4:E) must
be installed on the steering column between the
steering column jacket and the bracket as follows.
1. Install the steering column jacket on the steer-
ing column and secure by knocking in the cotter
pin (4:C) approximately 1/3 of its length.
2. Pull the steering column jacket and the steering
column up.
3. From the outside, check whether no washers,
the 0.5 mm washer, the 1.0 mm washer or both
washers can be inserted into the gap. The wash-
er/washers must not be forced in, as there must
be a little axial play.