manualshive.com logo in svg

Motorola PTP 300 Series, Руководство пользователя, Страница: 241 / 288

Поделиться
Скачать
Motorola PTP 300 Series Скачать руководство пользователя страница 241

 

 

16 PTP 300 Reference Information 

 

221

 

 

16.2  PTP 54300 Reference Information 

This section contains reference information for the PTP 54300 frequency variant. 

16.2.1 PTP 54300 Examples of Regulatory Limits 

Table 29 shows how the regulatory limits currently apply in specific countries. Operators 

should note that regulations are subject to change. 

Table 29 – PTP 54300 Examples of Regulatory Limits 

Region 

Examples of Regulatory Limits at 5.4GHz 

FCC 

Under FCC Regulations, operation of this product is only allowed with a License 
Key for Region 12.  This implements Radar Detection in accordance with FCC 
Regulations and limits the EIRP to the regulatory limits below: 

EIRP 

≤

 Max of [(17 +10 x Log(Channel BW)) and 30] dBm 

ETSI 

Under ETSI Regulations, operation of this product is only allowed with a License 
Key for Region 26.  This implements Radar Detection in accordance with ETSI 
Regulations, including barring of the band from 5600 MHz to 5650 MHz and 
limits the EIRP to the regulatory limits below: 

EIRP 

≤

 Max of [(17 +10 x Log(Channel BW)) and 30] dBm 

Canada 

Under Industry Canada Regulations, operation of this product is only allowed 
with a License Key for Region 13.  This implements Radar Detection in 
accordance with Canadian Regulations, including barring of the band from 5600 
MHz to 5650 MHz and limits the EIRP to the regulatory limits below: 

EIRP 

≤

 Max of [(17 +10 x Log(Channel BW)) and 30] dBm 

 

General Notice Applicable to Europe – 5.4 GHz 

This equipment complies with the essential requirements for the 
EU R&E Directive 1999/5/EC. 

 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Содержание PTP 300 Series

































































































































































































































































































Отзывы:

Нет отзывов