Motorola PTP 300 Series Скачать руководство пользователя страница 21

Страница: 21 / 288

1 About This User Guide

1 About This User Guide

Congratulations on the purchase of the PTP 300 Series Bridge from Motorola. The PTP 300

Series Bridge is the latest innovation in high-speed wireless networking that lets you deploy

wireless networks in areas previously unattainable.

This guide describes the installation, commissioning, operation and fault finding of the

Motorola PTP 300 Series of Point-to-Point Wireless Ethernet Bridges. It contains the following

main sections:

•

2 Product Description

•

3 Product Features

•

4 Planning Considerations

•

6 Installation

•

7 Web Page Reference

•

8 Recovery Mode

•

5 Lightning Protection

•

9 Troubleshooting (Fault Finding)

•

10 Connectorized PTP 300 Series Bridge

•

11 E1/T1 Installation Guide

•

12 Data Rate Calculations

•

13 AES Encryption

•

14 Remote Software Upgrade by TFTP

•

15 Legal Notices

•

16 PTP 300 Reference Information

1.1 Who Should Use This Guide

The guide is for use by the system installer and the end user IT professional. The system

installer will require expertise in the following areas:

•

Outdoor radio equipment installation

•

Network

configuration

•

Use of web browser for system configuration, monitoring and fault finding

4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299

Содержание PTP 300 Series

































































































































































































































































































Результаты поиска

Содержание PTP 300 Series

Отзывы:

Motorola PTP 300 Series, Руководство пользователя, Страница: 21 / 288

Результаты поиска

Содержание PTP 300 Series

Отзывы: