manualshive.com logo in svg

Motorola PTP 300 Series, Руководство пользователя, Страница: 24 / 288

Поделиться
Скачать
Motorola PTP 300 Series Скачать руководство пользователя страница 24

 

 

1 About This User Guide 

 

4

 

1.4  Getting Additional Help 

To get information or assistance as soon as possible for problems that you encounter, follow 

this procedure: 

1.  Search this document, the user manuals that support the modules, and the software 

release notes of supported releases: 

i.  In the Table of Contents for the topic. 

ii.  In the Adobe Reader® search capability for keywords that apply (Reader is a 

registered trademark of Adobe Systems, Incorporated).  

2.  Visit the Motorola website at www.motorola.com/ptp 

3.  Ask your Motorola products supplier to help. 

4.  Gather information from affected units such as: 

i.  the IP addresses and MAC addresses 

ii.  the software releases 

iii.  the configuration of software features  

iv.  any available diagnostic downloads 

5.  Escalate the problem to Motorola Technical Support as follows. You may either: 

i.  Send e-mail to [email protected] 

ii.  Call our 24x7 Technical Support Center on +1 (0) 877 515 0400 (Worldwide) 

or +44 (0) 808 234 4640 (UK Customers). 

For warranty assistance, contact your reseller or distributor for the process. 

1.5  Repair and Service  

For unit repair or service, contact your service provider or an authorized Motorola Point-to-

Point Distributor for Return Material Authorization (RMA) and shipping instructions. 

Alternatively, contact the PTP Global Technical Support Center to process an RMA. 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Содержание PTP 300 Series

































































































































































































































































































Отзывы:

Нет отзывов