manualshive.com logo in svg

Motorola PTP 300 Series, Руководство пользователя, Страница: 116 / 288

Поделиться
Скачать
Motorola PTP 300 Series Скачать руководство пользователя страница 116

 

 

7 Web Page Reference 

 

96

 

Figure 51 - Reset Configuration and Reboot Confirmation Pop-up 

 

 

On confirmation the PTP 300 Series Bridge will: 

•

 

Upload the configuration file 

•

 

Perform data integrity checking  

•

 

Erase previous configuration 

•

 

Apply the new configuration 

•

 Restart 

After the unit has restarted the entire configuration from the configuration file will now be 

active. The IP address of the unit may have also been changed. The user can check the new 

IP address by reading the header of the configuration file, Figure 49. 

CAUTION

 

A reboot is always required to restore a configuration file. 

 

4Gon   www.4Gon.co.uk   [email protected]   Tel: +44 (0)1245 808195   Fax: +44 (0)1245 808299 

Содержание PTP 300 Series

































































































































































































































































































Отзывы:

Нет отзывов