MOTO GUZZI V750 IE Скачать руководство пользователя страница 97

Страница: 97 / 113

Checking the connecting rod

•

Measure connecting rod pin diameter across the pin and again at 90° degrees away. Meas-

ure bearing seats on both timing system and flywheel side at the half-bearing locations.

•

Assemble the connecting rod without half-bearings and tighten the connecting rod screws

to the prescribed torque. Measure the outer diameter of half-bearing locations with a dial

gauge graduated in hundredths of a millimetre and the thickness of both half-bearings with

a round tip micrometer.

•

Check the bushings pressed in the small end of the connecting rod for notches due to seizing

or deep scoring; replace as required.

Seat diameter 43.657-43.670 mm (1.7188 - 1.7193 in).

Shaft diameter 39.995-40.001 mm (1.5746 - 1.5748 in).

Clearance between shaft and connecting rod bearing at 90° away from mating faces: min 0.020 (0.0008

in), max 0.061 (0.0024 in).

ONNECTING

ROD

BEARING

THICKNESSES

STANDARD (stock production) A mm (in)

STANDARD (stock production) B mm (in)

1.537-1.543 (0.0605 - 0.0607)

1.527-1.533 (0.0601 - 0.0603)

IAMETER

PRESSED

SMALL

END

BUSHING

AND

PISTON

PIN

INNER ø FOR PRESSED SMALL END

BUSHING mm (in)

PISTON PIN ø

MOUNTING CLEARANCE BETWEEN

SMALL END BUSHING AND PISTON

PIN mm (in)

18.010-18.020 (0.7090 - 0.7094)

17.996-18.000 (0.7085 - 0.7087)

0.010-0.024 (0.0004 - 0.0009)

Engine V750 IE

Engine

ENG - 97

Содержание V750 IE


















































































































Результаты поиска

Содержание V750 IE

Отзывы:

Похожие инструкции для V750 IE

Бренды по названию

Популярные бренды

MOTO GUZZI V750 IE, Руководство по обслуживанию станции

Результаты поиска

Содержание V750 IE

Отзывы:

Похожие инструкции для V750 IE

Бренды по названию

Популярные бренды