MOTO GUZZI V750 IE Скачать руководство пользователя страница 107

Страница: 107 / 113

OIL PUMP DRIVE SHAFT

Check shaft and thread for damage; check the

keyway for burrs and make sure the head the runs

in the rotor is not damaged; replace the shaft if

needed.

Shaft specifications:

•

Ø for pump body seat 11.982 - 12.000

mm (0.4717 - 0.4724 in);

•

Ø for needle bearings 9.991 - 10.000

mm (0.3933 - 0.3937 in);

FITTING CLEARANCES

•

between pump body and external rotor

0.080 - 0.135 mm (0.0031 - 0.0053 in);

•

between internal rotor bore and drive

shaft 0.016 - 0.061 mm (0.0006 -

0.0024 in);

•

between internal body bore and drive

shaft 0.016 - 0.061 mm (0.0006 -

0.0024 in);

Installing

•

Assemble the oil pump and refit it to the

crankcase, paying attention to the two

alignment dowels.

•

Tighten the Allen screws to the prescri-

bed torque and make sure the driving

shaft turns freely.

Engine V750 IE

Engine

ENG - 107

Содержание V750 IE


















































































































Результаты поиска

Содержание V750 IE

Отзывы:

Похожие инструкции для V750 IE

Бренды по названию

Популярные бренды

MOTO GUZZI V750 IE, Руководство по обслуживанию станции

Результаты поиска

Содержание V750 IE

Отзывы:

Похожие инструкции для V750 IE

Бренды по названию

Популярные бренды