MOTO GUZZI Engine V1100 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 108

background image

ENGINE

3 - 30

Engine V1100

3.5.3.

CHECKING THE COMPONENTS

HEADS

Make sure that:

•

Surfaces in contact with the cover and cylinder are not
scratched or damaged to the point where they
compromise sealing.

•

Check that clearance between valve guide holes and
valve stems is within the recommended limit.

•

Check valve seat condition.

VALVE GUIDES

Use a drift to remove the valve guides from the heads.
The valve guides should be changed only if clearance
between them and the valve stem cannot be eliminated by
changing the valves only.
To fit the valve guides to the head proceed as follows:

•

Heat up the head in an oven at about 60°C (140°F).

•

Lubricate the valve guides.

•

Fit the circlips.

•

Press the valve guides using a drift.

•

Using a bore reamer, grind the holes where the valve
stem slides, taking the inner diameter to the specified
value. Interference fit of the seat on the head and valve
guide should be 0.046 - 0.075 mm (0.0018 - 0.0030 in)

VALVE-TO-GUIDE COUPLING

INNER ø OF

VALVE GUIDE

mm (in)

VALVE STEM ø

mm (in)

ASSEMBLY

CLEARANCE

mm (in)

Intake

8.000-8.022 (0.3150-0.3158)

7.972

÷

7.987 (0.3139

÷

0.3145) 0.013-0.050

(0.0005

÷

0.0020)

Exhaust

8.000-8.022 (0.3150-0.3158)

7.965

÷

7.980 (0.3136

÷

0.3142)

0.020

÷

0.057 (0.0008

÷

0.0022)

«
...
55
56
57
58
59
...
»

Содержание Engine V1100













































































































Отзывы:

Нет отзывов

Похожие инструкции для Engine V1100

Бренд: SAESHIN Страницы: 2

Бренд: Schweigen Страницы: 28

Jeep Six-Cylinder

Бренд: Golen Страницы: 11

LYCOMING 200-6XL Series

Бренд: E-MAG Страницы: 30

Бренд: Scania Страницы: 55

Бренд: Pacific Страницы: 48

Бренд: AL-KO Страницы: 132

Бренд: Eastwood Страницы: 20

Бренд: Panther Страницы: 7

Бренд: Chicago Pneumatic Страницы: 100

Бренд: DETROIT Страницы: 84

TWINMOT T2-PLUS H

Бренд: Germany Motions Страницы: 12

Бренд: DANA Страницы: 2

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: O.S. engine Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды