Moss Automobile Parts Скачать руководство пользователя | Manualshive

Страница: 33 / 52

background image

M:\Product Information\366-348\Instructions\366-348 MGB Fuel Injection Installation Instructions_Grant_2.doc

Part 18, continued

366-348 Inst Fig 138

217.

Replace the plastic plug/grommet in the hole in the

trunk floor and push the hose through the hole in the
plug and into the trunk. (Fig 138)

218.

From inside the trunk, pull the hose until you have

taken up most of the slack. (figure 139)

366-348 Inst Fig 139

219.

Go back over the route of the hose, adjusting it as

needed to relieve stress and to route the hose around
sharp edges or other hazards. Zip-tie the hose to the
hard lines and/or other hoses where appropriate. From
inside the trunk, pull in any remaining slack if necessary.
This is as much as we can do with this hose at this time.

This completes part 18 of the installation

Installation Part 19 – Connecting the High Pressure Fuel Pump

220.

Find the following:

366-348 Inst Fig 165

165.1

165.2

one high pressure pump
four small hose clamps
a 36 inch length of 5/16” fuel hose
a 24 inch length of 5/16” fuel hose
All of these are in the kit.

221.

Examine the pump. One end (165.1) has electrical

connectors. The other end (165.2) does not. The hose
fittings have already been installed, and you will see
Teflon tape on the threads of the fittings.

For the next

several steps, we will be working with the fuel pump
suspended or hanging underneath the car because we
have found that once mounted, it is very hard to get to
the pump.

Page 33 of 52

«
...
31
32
33
34
35
...
»

Содержание Automobile Parts





















































Отзывы:

Нет отзывов

Похожие инструкции для Automobile Parts

Бренд: cam Страницы: 2

Бренд: Dapper Lighting Страницы: 2

Бренд: Samsung Страницы: 133

Бренд: VanEssa mobilcamping Страницы: 8

Бренд: Mazda Страницы: 527

2008 Escalade EXT

Бренд: Cadillac Страницы: 496

X-ACT CONTOUR 53491

Бренд: HUSKY LINERS Страницы: 2

Бренд: Volvo Страницы: 19

Бренд: Wagan Страницы: 8

Бренд: Thermo King Страницы: 2

Бренд: Kia Страницы: 10

PERFECTVIEW CAM80AHD

Бренд: Dometic Страницы: 196

Бренд: STC Страницы: 6

Бренд: Whispbar Страницы: 17

Бренд: Cadillac Страницы: 352

Бренд: SilverLeaf Electronics Страницы: 16

Бренд: Ranger design Страницы: 22

FABIA II TMB PS 035

Бренд: Skoda Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды