Moss Automobile Parts Скачать руководство пользователя

Страница: 13 / 52

M:\Product Information\366-348\Instructions\366-348 MGB Fuel Injection Installation Instructions_Grant_2.doc

366-348 Inst Fig 25

25.1

25.2

70. Locate the branch of the harness that has the relay

(25.1) and the inline fuse holders (25.2), and route it
over to the right hand side of the engine compartment.

Although missing in this particular picture, we encourage
the use of fender covers or towels to protect the paint.

71. Locate the branch of the harness with the molded plastic

connectors and carefully route it over toward the throttle
body. Take your time, and run the harness under the
heater hoses, behind vacuum lines and the stock wiring
harness bundle.

72. There will be a bundle of red-white wire hanging down

near the back of the engine. (see Fig 25C) This will
provide power for the new fuel pump and we will deal
with it when we run the fuel return hose.

366-348 Inst Fig 25C

This completes part 5 of the installation.

Page 13 of 52

Содержание Automobile Parts





















































Результаты поиска

Содержание Automobile Parts

Отзывы:

Похожие инструкции для Automobile Parts

Бренды по названию

Популярные бренды

Moss Automobile Parts, Руководство пользователя

Результаты поиска

Содержание Automobile Parts

Отзывы:

Похожие инструкции для Automobile Parts

Бренды по названию

Популярные бренды