Moss Automobile Parts Скачать руководство пользователя | Manualshive

Страница: 42 / 52

background image

M:\Product Information\366-348\Instructions\366-348 MGB Fuel Injection Installation Instructions_Grant_2.doc

Part 22, continued

366-348 Inst Fig 235

281.

Reinstall the carbon canisters, remembering to

tighten the nuts inside the cockpit. Reinstall the
windshield washer bottle bracket, replace the washer
bottle lid, reconnect the wires for the washer pump, and
reconnect the run-on control valve. (Fig 235)

282.

Back into the passenger’s side footwell.

366-348 Inst Fig 236

366-348 Inst Fig 237

366-348 Inst Fig 239

366-348 Inst Fig 238

236.1

283.

Position the ECU with the mounting flanges up and

the rectangular white plastic plug receptacles facing the
passenger seat. (Fig 236)

284.

Find the #8 x 1” self-tapping screws supplied in the

kit and slip one through the left rear hole in the mounting
flange (236.1).

Remember, rear is toward the back of the

car…

285.

Slip a plastic spacer over the screw. (Fig 237)

286.

Take a small piece of masking tape and stretch it

over the screw to hold the screw and spacer in place on
the ECU while you install it. (Fig 238 & 239)

287.

Repeat with two additional screws on the right-hand

side next to the kick panel.

288.

Hold the ECU with the three screws and spacers up

against the sheetmetal, lining up the screws with the
three hole locations. Gently /carefully start each screw.
Once all three screws are started, pull the tape out. Then
tighten the screws to secure the ECU in place (do not
over tighten the screws or they will strip out!). (Fig 240)

366-348 Inst Fig 240

Page 42 of 52

«
...
40
41
42
43
44
...
»

Содержание Automobile Parts





















































Отзывы:

Нет отзывов

Похожие инструкции для Automobile Parts

Бренд: AC Schnitzer Страницы: 16

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 7

Бренд: DANA Страницы: 42

Бренд: dallara Страницы: 37

Бренд: Yakima Страницы: 8

Бренд: Pivot Страницы: 4

Бренд: AccuAir Страницы: 40

Бренд: Peak Страницы: 10

1973 Crown Hardtop

Бренд: Toyota Страницы: 50

Бренд: B-Speech Страницы: 24

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Бренд: Vauxhall Страницы: 259

Бренд: Yutrax Страницы: 8

1966 Spider 105

Бренд: Alfa Romeo Страницы: 46

Бренд: DRAGONFIRE Страницы: 4

Бренд: ECS Electronics Страницы: 42

Бренд: Speedtech Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды