MORryde Aie1 Скачать руководство пользователя страница 6

INTRODUCTION

Guidelines for Adding or 

Removing Air Pressure 

 
When preparing to head out for a 
drive, make sure the suspension height 
indicators are in the green zone. Use your 
remote, mobile app, or Schrader valve to 
add or remove air as needed.

When loading or unloading a vehicle 
into the garage of the trailer, it is 
recommended to kneel the trailer 
by exhausting air spring pressure to 
approximately 5 PSI.

 

Increase air pressure in the system to 
overcome temporary obstacles and raise 
ground clearance.

The MORryde Air1 system controls air suspension height on your trailer using a remote and/or a mobile app to control air 
pressure. There are three main components to this system:

Suspension Height Indicator

 

The suspension height indicator makes sure the trailer is 
operating within safe pressure and height zones. This is 
located on both sides of the air suspension in front of the 
tire

 (fig. A)

. The suspension height indicator points on and 

around a labeled green zone. When adjusting pressure 
in the system before towing the trailer, check that the 
indicators point in the green zone.

NOTE: 

If you lose power, use an external air source to inflate 

the air suspension through the Schrader valve, indicated in 

(fig. A)

 This method can also be used to exhaust and kneel 

the trailer.

Suspension  

Height Indicator

Green Zone

figure A

WARNING

    

Only tow the trailer when the suspension height indicators 
are in the green zone. Check the indicators and adjust air 
pressure as needed before towing the trailer.

Powerpack

 

The powerpack communicates wirelessly with the remote and mobile 
app to control the air pressure in your suspension. It includes the 
module and compressor and is located on the front crossmember 
between the A-Arms and behind the battery of the trailer.

Remote and/or Mobile App

 

Use the remote and/or mobile app to increase or decrease 
pressure and otherwise control and troubleshoot the MORryde 
Air1 system. 

Schrader Valve

1

2

3

Содержание Aie1





























Отзывы: