Moons' TSM24P Скачать руководство пользователя страница 5

Страница: 5 / 49

Rev. 1.0

0012072012

TSM24P User Manual

+86-400-820-9661

1 Introduction

Thank you for selecting the MOONS’ TSM24P Integrated Motor.The

TSM line of integrated step-servo motors combines servo technology

with an integrated motor to create a product with exceptional feature

and broad capability. We hope our commitment to performance, quality

and economy will result in a successful motion control project.

1.1 Features

• Programmable, Digital servo driver and motor in an integrated

package

• Operates from a 12 to 70 volt DC power supply
• Control Modes:

* Position Control
* Digital Signal type

Step & Direction
CW & CCW pulse
A/B Quadrature (Encoder Following)

• Communications:

* RS-232

• 5000 line (20,000 counts/rev) encoder feedback
• Available torque:

* TSM24P-3AG: Up to 2.4 Nm Continuous(3.0 Nm Boost)

• I/O:

* 4 optically isolated digital inputs, with adjustable bandwidth digital noise rejection filter,5 to

24 volts

* 3 optically isolated digital outputs, 30V/100 mA max.
* Differential encoder outputs (A±, B±, Z±), 26C31 line driver, 20 mA sink or source max

• Technological advances:

*  Full servo control, Closed loop
*  Efficient, Accurate, Fast, Smooth
*  Intelligent, Compact

Содержание TSM24P


















































Результаты поиска

Содержание TSM24P

Отзывы:

Похожие инструкции для TSM24P

Бренды по названию

Популярные бренды

Moons' TSM24P, Руководство пользователя

Результаты поиска

Содержание TSM24P

Отзывы:

Похожие инструкции для TSM24P

Бренды по названию

Популярные бренды