Moons' TSM24P Скачать руководство пользователя страница 43

Страница: 43 / 49

Rev. 1.0

0012072012

TSM24P User Manual

+86-400-820-9661

Warnings
CCW Limit

when the DL (Define Limits) command is configured, Input#2 has been

triggered

CW Limit

when the DL (Define Limits) command is configured, Input#1 has been

triggered

Under Voltage

the DC bus voltage has dropped below 10 VDC

Move While Disabled

a move was commanded while the drive was disabled

Current Foldback

the command current exceeded either the boost or continuous limit

Blank Q Segment

does not apply to an S model

Flash memory

a flash memory error occured when saving parameters

NV Memory Error

the flash memory was found corrupted at power-up

Comm Error

the drive has detected a communications error either in the hardware

or in the protocol

6.7 Drive Status

The

Drive Status

is an overall indication of the drive condition.

In a typical application this is the most common information that

should be collected from the drive. Collecting the drive status

information allows the system controller to keep track of drive

operations and conditions.

Drive Status
Enabled

the drive is enabled and ready for moving operations

Tuning

the drive is in the process of tuning data capture

Fault

an alarm fault condition has occured (check Alarm Status)

InPosition

command position is within the PL (Position Limit) range

Moving

a commanded move is in process

Jogging

commanded jogging is in process

Stopping

the motor is decelerating

WaitInput

a WI (Wait on Input) command is executing

Saving

drive is saving parameter data

Alarm

an Alarm Code is present

Homing

the SH (Seek Home) command is executing

Delay

a WT (Wait Time) command is executing

Q Programing

does not apply to an S model

Initializing

the drive is in the process of power-up initialization

Содержание TSM24P


















































Результаты поиска

Содержание TSM24P

Отзывы:

Похожие инструкции для TSM24P

Бренды по названию

Популярные бренды

Moons' TSM24P, Руководство пользователя

Результаты поиска

Содержание TSM24P

Отзывы:

Похожие инструкции для TSM24P

Бренды по названию

Популярные бренды