Moons' SSM24C Скачать руководство пользователя

Страница: 31 / 50

Rev. 1.0

0006302011

SSM24C User Manual

+86-400-820-9661

5.5.2 Performing a Move

Once the move settings are correct the mechanism

to be moved shold also be checked to ensure it is

ready to move. It is especially important to make sure

the direction is set correctly. In some cases it is wise

to select

alternate

to avoid running the mechanism

into a hard stop. Select the

Sample Once

button.

Click the

Start

button and observe the results.

If problems occurred during the move an Alarm

indicating a Fault or Warning may be displayed and need to be cleared. The drive may be left

disabled until the Alarm is cleared and the Enable button is clicked.

Note: Clicking the Alarm Reset button and then the Enable button will clear a fault and

enable the drive.

Now the motion parameters will need to be adjusted to achieve the desired move profile. The

move can be repeated by clicking the

Start

button. If the drive continues to fault it is possible the

maximum current or position error parameters are being exceeded. These can be set in the

Drive

Configuration

tab.

The current setting can be checked by selecting

Current

in one of the Plot lists and clicking

Start

again to see what current is being required of the

drive during a move. The current profile of the move

will be displayed and may give a clue as to why a

fault is occurring.

5.5.3 Adjusting tuning parameters

The two primary parameters for a Timed move are

the

Proportional

(VP) &

Integral

(VI) gain parameters of the velocity loop.

Starting with these two terms is a good way to begin tuning as they are the minimum required

terms in Velocity Loop tuning. The

FF Gain

is not

required but adds to the tuning, this will be discussed

later.

Note 1:

The

Disable

button in the Menu bar of the

SSM Quick Tuner window under the label

Servo

will

disable the motor should a serious problem occur.

Note 2:

The Gain values can be changed at any

time during the tuning process. When the SSM

Quick Tuner software detects a change in the value

it will automatically download the new value. The

Download

button in the upper right of the window

does not need to be clicked.

Once a successful move has been accomplished (no

fault occurs) the motor is ready for tuning. Adjust the

Содержание SSM24C



















































Результаты поиска

Содержание SSM24C

Отзывы:

Похожие инструкции для SSM24C

Бренды по названию

Популярные бренды

Moons' SSM24C, Руководство пользователя

Результаты поиска

Содержание SSM24C

Отзывы:

Похожие инструкции для SSM24C

Бренды по названию

Популярные бренды