Moons' SSM24C Скачать руководство пользователя | Manualshive

Страница: 18 / 50

background image

18

Rev. 1.0

0006302011

SSM24C User Manual

+86-400-820-9661

drive stores up to 8 sets of alarm conditions. The Alarm History dialog can also be used to clear

the Alarm History.

4.1.4 LED Flashing

Clicking on this button will bring up a screen where the LED flashing for certain warnings can be

masked. Alarm fault conditions are not allowed to be masked and will always be indicated by the

drive’s LEDs. Masking alarm warnings only prevents the indication of the alarm by the LEDs. The

alarm warning will still be set in the Alarm status code and in the Alarm History. See section 7 on

“Troubleshooting” below for an explanation of these codes.

4.1.5 Drive & Revision

When SSM Quick Tuner is connected to an SSM Integrated Motor the drive model, sub-model,

and firmware revision are automatically indicated. If working offline (no drive is connected), the

Drive model and sub-model can be selected from the drop down lists. The model and sub-model

information is found on the label of the SSM integrated motor.

4.1.6 Communication

«
...
16
17
18
19
20
...
»

Содержание SSM24C



















































Отзывы:

Нет отзывов

Похожие инструкции для SSM24C

Бренд: Danfoss Страницы: 54

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 197

Бренд: Danfoss Страницы: 284

Бренд: Danfoss Страницы: 53

Бренд: Fastech Страницы: 40

Бренд: TQ Страницы: 28

Penta Power KBRG-255

Бренд: KB Electronics Страницы: 20

Бренд: Oray Страницы: 3

ACTIVE CUBE Series

Бренд: BONFIGLIOLI Vectron Страницы: 200

CoolDrive Series

Бренд: Tsino Dynatron Страницы: 285

Бренд: Hafele Страницы: 84

Бренд: Simu Страницы: 20

Бренд: KEBCO Страницы: 24

Бренд: Melec Страницы: 53

CIPR-CR70A Series

Бренд: YASKAWA Страницы: 773

Бренд: Danaher Motion Страницы: 68

ACS880-01 Series

Бренд: ABB Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды