VFI33 Vent Free Gas Fireplace System
20307670
7
PRE-INSTALLATION INFORMATION
GETTING STARTED
Make sure you have received all parts
Check your packing list to verify that all listed parts have
been received. You should have the following:
•
Installation/Operating instructions
•
33" unvented gas heater
•
Canopy
•
Volcanic rock and rock wool (traditional sets only)
•
Stone and fireglass kit (contemporary sets only)
•
Two (2) anchoring screws
•
Mounting screws for canopy
Accessories required to finish the installation:
One of two surrounds:
•
VFICFSS
Black small surround 33"H x 43"W
•
VFICFSL
Black large surround 36"H x 50"W
One of three firebox liners:
•
FBVFIC(M/LR) Firebrick
•
BLPVFIC
Black porcelain panels
•
BMGVFIC
Black Magic glass panels
WHAT YOU WILL NEED FOR INSTALLATION
You must have the following items available before pro-
ceeding with installation:
•
External regulator (for propane / L.P.G. and 1/2 lb.
Natural Gas systems only)
•
Piping which complies with local codes
•
Sediment trap
•
Tee joint
•
Pipe wrench or appropriate size crescent wrench
set
•
Phillips head screwdriver
•
Drill with 5/32" bit
•
Surround
•
Manual shutoff valve
•
Pipe sealant approved for use with liquid propane
(resistant to sulfur compounds)
FRAMING DIMENSIONS
If unit is to be “built in,” fireplace framing can be built before
or after the appliance is set in place.
BE SURE THAT ALL
PACKING MATERIAL HAS BEEN REMOVED FROM
THE UNDERSIDE OF THE UNIT PRIOR TO SETTING
THE FIREBOX IN PLACE.
Construct fireplace framing
following Figure 3 on page 6. The framing headers may
not rest directly on top of the firebox.
The fireplace may be installed directly on a combustible
floor or a raised platform of an appropriate height. Do
not place fireplace on carpeting, vinyl, tile or other soft
floor coverings. It may, however, be placed on flat wood,
plywood, particle board or other hard surfaces. Be sure
fireplace rests on a solid continuous floor or platform with
appropriate framing for support and so that no cold air can
enter from under the firebox. Your vent-free fireplace must
be mounted to the floor or the fireplace hearth.
The millivolt controlled version of this heater is the only
style designed to be operated with optional devices for
ON/OFF functions. The following options may be used
with the millivolt controlled heater. These options are
not
packaged with the unit.
•
Hand held Remote with Receiver
•
Wall switch with 15' wire.
•
Hand held Thermostat Remote with Receiver
IPI controlled versions of this unit have the following options
that may be used but are not packaged with the unit.
• IPIFKN2: Stepper motor kit (NG)
• IPIFKP2: Stepper motor kit (LP)
Carefully inspect the contents for shipping damage. If any
parts are missing or damaged, immediately inform the
dealer from whom you purchased the appliance. Do not
attempt to install any part of the appliance unless you have
all parts in good condition.
•
Handle the gas log burner assembly by the
grate only. Do not pick the unit up by the
burners.
•
Gloves are recommended when handling
ceramic fiber logs to prevent skin irritation
from loose fibers. Logs are fragile — handle
with care.
WARNING:
WARNING—Do not install the heater:
•
Where curtains, furniture, clothing, or
other flammable objects are less than
42" from the front of the heater.
•
In high traffic areas.
•
In windy or drafty areas.
WARNING: If the area in which the heater
is operated does not meet the required
volume for indoor combustion air, combustion
and ventilation air shall be provided by one of
the methods described in the
National Fuel Gas
Code, ANSI Z223.1/NFPA 54
, the
International
Fuel Gas Code
or applicable local codes.
