background image

5

NB18/NB24 Gas Log Set

Monessen • NB18/24 Gas Log Set Installation/Owner's Manual • 81D0107 • Rev E • 04/18

CHECK PARTS:

Verify contents to ensure you have received all parts. You 

should have the following:

NB Models

 

  Unvented gas log burner assembly 

 

  Two (2) bags of crushed volcanic rock 

 

  Installation/operating instructions 

 

  Two (2) Anchoring Screws

 

  Ceramic fiber or refractory logs 

 

• 

Rock wool

 

  Grate assembly 

 

  On/off log switch assembly (MV models only)

 

  Thermostat remote control (SCR models only)

 

  Double A batteries (SC models only) 

The following options may be used with the millivolt con-

trolled heater. These options are 

not

 packaged with the 

log set.
 

  Hand-held remote with receiver (MV) 

 

  Wall thermostat with 15' wire

 

  Wall switch with 15' wire 

Carefully inspect the contents for shipping damage. If any 

parts are missing or damaged, immediately inform the 

dealer from whom you purchased the appliance. 

Do not 

attempt to install any part of the appliance unless you 

have all parts in good condition.

ITEMS NEEDED FOR INSTALLATION:

You should have the following items available before pro-

ceeding with installation:
 

  External regulator (for propane/LPG and 1/2 psi 

natural gas systems only)

 

  Piping which complies with local codes

 

  Sediment trap (recommended) 

 

 Screwdriver

 

  Tee joint.

 

  Pipe sealant approved for use with propane/LPG 

(Resistant to sulfur compounds)

 

  Drill with 5/32 masonry bit 

 

  Pipe wrench or appropriate size crescent wrench 

set 

 

  Manual shutoff valve

PRODUCT FEATURES

Gloves  are  recommended  when  handling 

ceramic fiber logs to prevent skin irritation 

from loose fibers. Logs are fragile; handle 

with care.

CAUTION

GAS PRESSURES

Natural

Propane (LP)

Inlet Minimum

5.0" w.c.

11.0" w.c.

Inlet Maximum

10.5" w.c.

13.0" w.c.

Regulator Pressure 

Setting

3.5" w.c.

11.0" w.c.

Pilot Regulator

3.5" w.c.

n/a

NATURAL GAS:

 An external regulator is required to reduce 

supply pressure to a maximum of 10

1

2

" w.c. on natural gas 

systems operating at higher pressure. 

PROPANE/LPG:

 An external regulator is required to reduce 

supply pressure to a maximum of 13" w.c. 

MILLIVOLT IGNITION CONTROLS 

The piezo ignitor allows ignition of the pilot without the use 

of matches or batteries.

Millivolt control has four (4) positions:
OFF

:All gas to the gas logs is shut off at the valve.

IGN

 : Valve position to light/maintain a standing pilot.

ON

:  Valve position to turn ON/OFF log set with remote 

switch/thermostat.

LOW/HI

:  Variable  position  to  control  flame  height  (heat 

output).

SIGNATURE COMMAND CONTROLS

Refer to page 28.

PILOT/ODS

The gas log heater is fitted with a specially designed safety 

pilot (ODS assembly) which senses the amount of oxygen 

available in the room and shuts the gas log heater off if the 

oxygen level begins to drop below a satisfactory level. The 

pilot can only be relit when adequate fresh air is available.

THERMAL GENERATOR

The millivolt gas log pilot is fitted with a millivolt (thermopile) 

generator to provide power for remote activation.

GAS SPECIFICATIONS

 

 

Gas Rate

Max. Input

Min. Input

Model

Fuel

BTU/h

BTU/h

NB18

Natural

28,000

19,000

NB24

Natural

37,000

25,000

NB18

LP

27,000

22,000

NB24

LP

36,000

28,000

Содержание BC18-R























































Отзывы: