background image

Hand Crimp Tool for Micro-Fit 3.0 Crimp Terminals 

Doc. No: ATS-638280200  Release Date: 03-15-16 

UNCONTROLLED COPY

 

Page 1 of 7 

Revision: C 

Revision Date: 06-18-19 

CONDUCTOR 

BRUSH 

STRIP LENGTH 

CONDUCTOR 

CRIMP 

CUT-OFF 

TAB 

BELL 

MOUTH 

BEND UP 

TWIST 

ROLL 

BEND 

DOWN 

SEAM 

INSULATION 

CRIMP 

 

 

Application Tooling Specification 

 

FEATURES 

 

 

A full cycle ratcheting hand tool ensures complete crimps 

 

Ergonomic soft grip handles for comfortable crimping 

 

A precision user-friendly terminal locator with wire stop holds terminals in the proper crimping 
position 

 

Dies and locator from this tool can be used in the Battery Powered Tool Order No. 63816-0270 
(110 V) or 63816-0280 (220 V) with the use of the 63816-0800 Crimp Head 

 

Many different tool kits can be used with a single Battery Powered Crimp Tool 

 

This tool is IPC/WHMA A-620 Class 2 compliant (see Scope table) 

 

This tool is RoHS compliant; however, RoHS compliance is not required 

 

SCOPE 

 

Products:

 Micro-Fit 3.0 Crimp Terminals, 0.75mm

2

 and 18 AWG (UL1061) wires. 

 

Terminal 

Series No. 

Terminal 

Order No. 

Wire Size 

Insulation Diameter 

Strip Length 

IPC/WHMA-A-620 (1) 

Terminal (2) 

AWG  mm² 

mm 

In. 

mm 

In. 

mm 

In. 

43030 

43030-0038 

18 

0.75 

1.60-1.85 

.063-.073 

0.90-1.85  .035-.073  2.54-2.92  .100-.115 

43031 

 

(3)

 

43031-0021 
43031-0022 
43031-0023 

45807 

45807-0003 

18 

— 

45807-0005 

203951 

203951-0001 

18 

— 

Insulation Diameter Notes 

(1) Insulation OD range for optimum (IPC/WHMA-A-620 Class 2) insulation crimps 
(2) Insulation OD range for the terminal product design 

 

Terminal Locator Note 

(3) Separate terminal locator is needed for 43031 series (see page 2). If locator is missing it can be ordered (see page 7) 

 

DEFINITION OF TERMS 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Order Number 

63828-0200 

Type 4D 

Содержание 63828-0200








Отзывы: