Mohawk A-7 страница 4 Скачать руководство пользователя | Manualshive

Страница: 4 / 74

background image

MOHAWK MODEL A-7

iii

CEILING HEIGHT WARNING

WARNING:

Ensure that ceiling height* and/or overhead hydraulic line height is greater than the total
lifted height of the tallest vehicle (maximum vehicle height plus lift stroke). Failure to
ensure adequate overhead clearance may cause damage to equipment, vehicle and bodily
injury to the user.

NOTICE:

In the event that the ceiling height* or hydraulic line height is reduced less than the
standard heights recommended for the lift, an

OVERHEAD SHUT-OFF DEVICE

MUST BE EMPLOYED.

Note that underground hydraulic lines are available, but the ceiling height* must still be
adequate to provide clearance for the tallest lifted vehicle. Ensure that the whole fleet of
vehicles is reviewed and the tallest vehicle used.

*Overhead obstruction of any kind must be taken into account (i.e. overhead heaters,
garage doors, beams, etc..)

«
...
2
3
4
5
6
...
»

Содержание A-7











































































Отзывы:

Нет отзывов

Похожие инструкции для A-7

Бренд: Zehnder Rittling Страницы: 36

Бренд: S&S Northern Страницы: 9

Бренд: ShoreStation Страницы: 15

Бренд: Woodward Страницы: 112

Бренд: GANTERUD Страницы: 24

Бренд: fadini Страницы: 20

Бренд: Sensitron Страницы: 11

Бренд: Logic Страницы: 3

Бренд: ADLINK Technology Страницы: 37

Бренд: VENCO Страницы: 52

Бренд: Jasic Страницы: 18

Бренд: M-system Страницы: 19

Бренд: jbc Страницы: 20

Бренд: M-system Страницы: 3

AMETEK ORBIT ACS Series

Бренд: Solartron Metrology Страницы: 63

Бренд: 2VV Страницы: 24

20/20 SeedSense

Бренд: Precision Planting Страницы: 65

Бренд: LGMG Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды